background image

2

TABLE OF CONTENTS

COPYRIGHT NOTICE ....................................................................................................................................................................................................... 2

SAFETY INSTRUCTIONS ................................................................................................................................................................................................. 2

INTRODUCTION ............................................................................................................................................................................................................... 3

GETTING STARTED WITH CART .................................................................................................................................................................................... 4

OPERATION OF MOBILE POWER CART ....................................................................................................................................................................... 7

MAINTENANCE & REPLACEMENT PARTS LISTS ......................................................................................................................................................... 11

WIRING DIAGRAM ........................................................................................................................................................................................................... 15

BASIC TROUBLESHOOTING ........................................................................................................................................................................................... 16

COPYRIGHT NOTICE

This manual is copyrighted.  All rights reserved.  This manual may be printed for personal use only.  This manual, whole 

or in part, may not be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-

readable form for distribution.  This manual, whole or in part, may not be modified without prior consent, in writing, from 

InterMetro Industries Corporation.

Copyright © 2012 by InterMetro Industries Corporation, 651 North Washington Street,  

Wilkes-Barre, PA 18705, U.S.A. 

Phone: 1-800-992-1776 

http://www.metro.com/support
InterMetro Customer Service: 

For all customer service related issues, or if you need technical assistance, please call 

our customer service department at:

1-800-992-1776 Americas
+31 76 58 77550  

Europe

+9714 811 8286 

Middle East

+65 6567 8003  

Asia-Pacific

SAFETY INFORMATION

This section contains important safety and operating instructions for Starsys mobile power cart.  Please read all 

instructions on the cart before putting into service.

CAUTION

:   User maintenance consists solely of cleaning and minor external adjustments.  For safety purposes, all 

servicing must be performed by qualified service personnel only.  For all service items, please contact 

InterMetro Customer Service.

CAUTION

:   Do not operate the Starsys cart, if it has received a severe impact or has been otherwise physically 

damaged.  Please have a qualified service person inspect both the Starsys cart in conjunction with its power 

supply for any performance or safety hazard prior to putting back into service.

CAUTION

:   To prevent damage to any cords or connectors when disconnecting, always grasp and pull by the connector 

and not the cord.  Do not operate the Starsys cart with damaged cords or connectors.  Please replace the 

damaged component immediately.  Contact InterMetro Customer Service for replacement parts and service.

DANGER:

   Starsys cart and the power supply are not for use in hazardous (classified) locations.  Do not use nor 

recharge the power supply battery, in oxygen enriched areas; areas where flammable anesthetics are used 

or stored; or any other hazardous, classified location.

DANGER:

   The maximum design load (safe working load limit) for the Starsys cart is 300 lbs.(136 kg.).

   

THE RECEIVER OF THIS PRODUCT IS RESPONSIBLE FOR FREIGHT DAMAGE CLAIMS

.

• 

This equipment must be opened immediately for inspection.

• 

All visible damages must be reported to freight co. within 

48 hours

, and must be noted on freight bill at time of 

delivery.

• 

Concealed damage is your responsibility - you must advice carrier of any loss or damage within 

15 days

 after 

receipt of material.

• 

If there is damage, retain original packaging for inspectors.

Summary of Contents for STARSYS WIRELESS

















Reviews: