SECTION 3 - M. FRAME, ADJ. RING, TRAMP REL. & CLRNG JACK ASSY
MP SERIES CONE CRUSHER TECHNICAL REFERENCE MANUAL
3-31
5. Remove the mounting bolts from the top of
the clamping cylinder refer to Figure 3-25.
6. Carefully slide the cylinder out of the
clamping ring.
3.4.14 Clamping Cylinder Disassembly and
Repair
For clamping cylinder disassembly and repair
procedure, refer to
Section 12
under
Clamping
Cylinder Rebuilding.
3.4.15 Clamping Cylinder Installation
To install a new or rebuilt clamping cylinder into
the clamping ring, refer to Figure 3-24 and proceed
as follows:
1. With the clamping ring on blocking (a
minimum of 310 mm (12") coat the
clamping cylinder with “Never Sieze,” then
slide the cylinder up into its mating hole in
the clamping ring until it bottoms. Then
block the cylinder in place to hold it up.
NOTE:
On the MP1000 make sure the
hydraulic fitting is screwed into the top of the
cylinder before sliding the cylinder into the
clamping ring.
2. MP1000
a. Turn the clamping cylinder so the
mounting holes are in line with the
dowel in the clamping ring.
b. Place the two spacers on the cylinder and
centered on the two tapped cylinder
mounting holes.
c. Place the mounting bracket, with it
engaging the dowel, on the spacers. Then
bolt in place with the mounting bolts.
MP800
a. Turn the clamping cylinder so the
mounting holes are in line with the
dowels in the clamping ring.
b. Place a spacer over each dowel.
c. Place the mounting bracket, with it
engaging the dowels on the cylinder,
then bolt it in place with the mounting
bolts.
3. Install the tee or elbow and hoses to the top
of the cylinder using Loctite 545 thread
sealant on the fitting connections.
4. To mount the clamping ring onto the
adjustment ring, follow the procedure under
Adjustment Ring Assembly
in this section.
3.4.16 Adjustment Ring Assembly
After inspection, repairs or replacement of parts,
the adjustment ring is placed back on the main
frame and the associated parts are assembled as
follows:
1. If the adjustment ring was removed liberally
coat the adjustment ring seat with a lithium
base grease, NLGI No. 1 containing a
minimum of 3% molybdenum disulfide. If
the adjustment ring was not removed and
just the clamping ring removed from the
adjustment ring, proceed to step 4.
2. Attach shackles and lifting slings to the lift
lugs, four on the MP1000, three on the
MP800, located on the outside diameter of
the adjustment ring, Refer to Figure 3-7 and
Figure 3-20.
3. Turn the adjustment ring so the clamping
cylinder hose connection, on the outside of
the ring, is opposite the countershaft box,
then lower the ring on the frame. As the
adjustment ring is lowered over the main
frame pins, rotate the ring in a clockwise
direction so the main frame pin bushings in
the adjustment ring touch the main frame
pins. Refer to Figure 3-21. Then lower the
ring in this position and allow it to seat on
the frame.
4. Install an M36 ring bolt in each of the two
tapped holes in the clamp ring and lift the
clamp ring.
5. Before lowering the clamp ring onto the
adjustment ring, turn the clamp ring so the
50 mm (2") dia. hole is vertically in line
with the hose connected to the top of the
adjustment ring. Slowly lower the clamp
ring over this hose and onto the adjustment
ring. Refer to Figure 3-26.
6. Insert spacers and hex head capscrews that
keep the clamp ring in place while turning
the bowl in or out inside the crusher. Turn
the capscrews into the adjustment ring until
they bottom on the spacers. There are eight
Summary of Contents for MP1000
