M o d e l V B 9 0 0
11 |
P a g e
PRE-OPERATION
GENERAL
Read the entire Owner’s Manual before attempting to
operate this manure spreader. Before attempting any
maintenance or repairs; always be sure all rotating parts
have stopped and that the tractor is shut off, dis- connect
the PTO, relieve all hydraulic pressure and disconnect
hydraulic hoses.
WARNING
NEVER OPERATE SPREADER WITH ANY GUARDS
OR SHIELDS REMOVED. FAILURE TO HEED MAY
RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
1. Completely lubricate the unit as described in the
LUBRICATION Section.
2. Check and tighten the wheel lug nuts if required.
3. Check and maintain the tire pressure according to
the manufacturer’s recommendation.
4. Check the entire unit for loose bolts, damaged or
loose hydraulic fittings and hoses or other damaged
parts.
5. The tractor half of the PTO drive shaft assembly must
be locked securely to the tractor output shaft.
TRACTOR HITCH AND PTO
REQUIREMENTS
This spreader is designed to be operated by a 1000 RPM
PTO tractor output.
The PTO drive shaft assembly is designed to operate
with tractors conforming to the industry standard shown
on figure 1 for 1000 RPM PTO output.
ADMA Recommendations:
A tractor drawbar equipped with a clevis hitch (hammer
strap) can cause interference with the PTO driveline IID
(implement input driveline). This interference can cause
serious damage to the IID or the IID telescoping
members. Verify there is sufficient clearance between
the IID and your particular clevis hitch.
If the implement (figure 2, lower view) is attached to a
tractor with an offset in the drawbar, be certain it is in
the down position to prevent damage to the IID
guarding or the IID telescoping members.
FIGURE 1. TRACTOR DRAWBAR & PTO
SPECIFICATION
FIGURE 2. PTO ALIGNMENT
Summary of Contents for VB900
