MFJ Compact IntelliTuner MFJ-928 Instruction Manual Download | Manualshive

Page: 25 / 28

background image

MFJ-928 Compact IntelliTuner Automatic Antenna Tuner

Instruction Manual

©

2005 MFJ Enterprises, Inc.

21

Technical Assistance

If you have any problem with this unit first check the appropriate section of this manual. If the manual
does not reference your problem or your problem is not solved by reading the manual, you may call

MFJ

Technical Service

at 662-323-0549 or the

MFJ Factory

at 662-323-5869. You will be best helped if you

have your unit, manual and all information on your station handy so you can answer any questions the
technicians may ask.

You can also send questions by mail to MFJ Enterprises, Inc., 300 Industrial Park Road, Starkville, MS
39759; by facsimile (FAX) to 662-323-6551; or by email to techinfo@mfjenterprises.com. Send a
complete description of your problem, an explanation of exactly how you are using your unit, and a
complete description of your station. Also include the firmware version number of your unit.

List of Accessories

•

MFJ-1316

:

12 VDC 1.5 amp power supply

•

MFJ-4116

:

BiasTee DC power injector

•

MFJ-5114A

: Interface cable for compatible Alinco radios

•

MFJ-5114I

:

Interface cable for compatible Icom radios

•

MFJ-5114K

: Interface cable for compatible Kenwood radios

•

MFJ-5114Y

: Interface cable for Yaesu FT-100, FT-817, FT-857 and FT-897 (CAT)

•

MFJ-5114Y2

: Interface cable for Yaesu FT-847 (CAT)

•

MFJ-5124Y3

: Interface cable for Yaesu FT-857 and FT-897 (TUNER)

•

MFJ-5409

:

6 feet long RS-232 cable, female DB-9 to male DB9 connector

•

MFJ-5803

:

3 feet long RG-58 A/U 50-ohm coax cable with a PL-259 connector on each end

•

MFJ-5806

:

6 feet long RG-58 A/U 50-ohm coax cable with a PL-259 connector on each end

•

MFJ-5818

:

18 feet long RG-58 A/U 50-ohm coax cable with a PL-259 connector on each end

«
...
23
24
25
26
27
...
»

Summary of Contents for Compact IntelliTuner MFJ-928





























Reviews:

No comments

Related manuals for Compact IntelliTuner MFJ-928

Brand: Ibanez Pages: 2

Brand: Ibanez Pages: 2

Brand: TC Electronic Pages: 2

Brand: Renkforce Pages: 4

Brand: CYP Pages: 44

Brand: Marantz Pages: 29

Brand: Onkyo Pages: 24

Brand: Eagletone Pages: 2

Brand: Yamaha Pages: 4

Brand: PCTV Systems Pages: 2

Brand: Tivizen Pages: 1

HD HomeRun PRIME

Brand: SiliconDust Pages: 6

Brand: SiliconDust Pages: 19

Brand: System Fidelity Pages: 15

Brand: Anritsu Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands