background image

MFJ-998RT Legal Limit IntelliTuner

TM

  Automatic Remote Antenna Tuner                    Instruction Manual

 

 

© 2011 MFJ Enterprises, Inc                                                                                                                    

 

MFJ-998RT Version 1A 

 

Features 

 

Automatically matches antennas from 12 to 1600 ohms impedance (SWR up to 32:1) 

 

Handles 1500 watts SSB/CW 

 

Tune in less than 20 seconds, usually less than 5 seconds 

 

Over 20,000 non-volatile memories for tuner settings 

 

Eight memory banks with over 2500 memories per bank 

 

Highly efficient switched–L network matching circuit 

 

1.8 to 30 MHz continuous frequency coverage 

 

Adjustable target SWR from 1.0 to 2.0 

 

Adjustable SWR threshold from 0.5 to 1.5 

 

Multifunction backlit LCD display with contrast control for testing and setup 

 

Numeric readings for SWR, forward and reflected power for testing and setup 

 

Bar meters for SWR, forward and reflected power with range options for testing and setup 

 

Audio SWR meter for testing and setup 

 

Built-in frequency counter for testing and setup 

 

Direct read-out of matching L/C values available after tuning for testing and setup 

Specifications 

 

Impedance matching range: 12 to 1600 ohms 

 

SWR matching range: up to 4:1 for < 50 ohms and up to 32:1 for > 50 ohms 

 

Minimum power for tuning: 5 watts 

 

Maximum power while tuning: 100 watts with foldback, 20 watts without foldback 

 

RF power limit: 1500 watts SSB/CW 

 

Frequency range: 1.8 to 30 MHz continuous coverage 

 

Frequency counter accuracy: ±1 kHz across HF bands 

 

Capacitance range: 0 to 3926 pF nominal (256 values) on input side 0 to 976 pF nominal (64 
values) on output side 

 

Inductance range: 0 to 24.28 

µ

H nominal (256 values) 

 

Relay rating: 16 amp 1000 volts 

 

Relay electrical life: 100,000 operations 

 

Relay mechanical life: 10 million operations 

 

Memory endurance: 1 million erase/write cycles 

 

Memory data retention: > 200 years 

 

Power requirements: 12 - 15 volts DC, 2.1 × 5.5 mm coaxial plug, center pin positive 

 

Current consumption: 1.4 amps or less 

 

Dimensions (approx.): 13 ¾ × 6 ¼ × 18 in. (350 × 159 × 457 mm) (width/height/depth) including 
connectors 

 

Weight (approx.): 9 lb. 8 oz. (4.3 kg) 

 

Operating Temperature -40 to +160 degrees F 

 
 

† Specifications and design are subject to change without notice. 

 
 
 
 

Summary of Contents for Legal Limit IntelliTuner MFJ-998RT





























Reviews: