16
17
- Sawing
Use undamaged faultless saw blades only. Deformed, blunt saw blades or saw blades that are
otherwise damaged can break.
Plunge cuts may only be applied to soft materials, such as wood, gypsum plaster boards, etc.!
Before sawing with saw blades in wood, particle board, building materials, etc., check these
for foreign objects such as nails, screws, or similar. If required, remove foreign objects or use
saw blades for metal.
- Sanding
The removal rate and the sanding pattern are primarily determined by the choice of sanding
sheet, the preset oscillation rate and the applied pressure.
Only flawless sanding sheets achieve good sanding capacity and extend the service life of the
machine.
Pay attention to apply uniform sanding pressure; this increases the working life of the sanding
sheets.
Intensifying the sanding pressure does not lead to an increase of the sanding capacity, but to
increased wear of the machine and the sanding sheet.
For precise on-the-spot sanding of edges, corners and hard to reach areas, it is also possible
to work only with the tip or an edge of the sanding plate.
When selectively sanding on the spot, the sanding sheet can heat up considerably. Reduce
the orbital stroke rate and allow the sanding sheet to cool down regularly.
A sanding sheet that has been used for metal should not be used for other materials.
- Scraping
For scraping, select a high oscillation rate.
Work on a soft surface (e.g. wood) at a flat angle and apply only light pressure. Otherwise the
scraper can cut into the surface.
TROUBLESHOOTING
WARNING: This tool is equipped with quick-install accessories during operating; do not
use any unmatched accessories.
WARNING: Check the tight seating of the application tool/accessory. Incorrect or not
securely fastened application tools/accessories can come loose during operation and
pose a hazard.
Problem
Possible cause
• Battery not installed properly
• Battery not charged
• Check battery installation
• Check battery charging
requirements
• Insert battery into charger
until red LED appears
• Plug Charger into working outlet.
Refer to “Important Charging
Notes” for derails
• Move chrger and tool to
a surrounding air temperature
of above +39.2°F(4°C) or below
104°F(40°C)
• Battery not installed into
charger
• Charger not plugged in
• Surrounding air temperature
too hot or cold
Possible solution
• Unit will not start
• Battery will not
charge
- Inserting and removing the battery
- Switch
(C in the functional description)
• To insert, simply push pack in until
lock spring clicks.
• To remove battery pack from the
tool, press the lock spring buttons
(d in the functional description)
and pull out.
• Make sure the battery pack is installed.
• To switch on, simply push the ON/OFF switch
trigger forward to position 1.
- Speed adjusting
(D in the functional description)
• The tool can be set at 6-speed adjustment
positions. The "1" position indicates the
lowest and the "6" position indicates the
speed by turning the speed control dial (D)
from "1" to "6" position. The operator may
have to vary the speed to optimize working
- Mounting sanding plate/ saw blade/ scraper
WARNING: Prior to assembly and adjustment always pull
out the battery pack.
• Take care with sharp tools such as spatulas, saw blades
or cutting blades.
• Loosen the clamping plate (b) by pulling the quick-re-
lease lever completely open.
• Hold the opening of the quick-install saw blade, sanding
plate or spatula toward the output spindle which between
cover clamp (a) and clamping plate (b), push the accesso-
ry in and place it firmly onto the locating pins (c).
• Fasten using the quick-release lever (B in the functional
description) at the lock position.
• Remove the accessory in the opposite way.
D
a
b
c
C
20V ULTRA Oscillating Multi-Tool 2Ah KIT
(MH-03-OT-B1-0-1)
20V ULTRA Oscillating Multi-Tool 2Ah KIT
(MH-03-OT-B1-0-1)
