Mhouse WT1S, Installation Instructions And Warnings, And User Manual

GENERAL SAFETY WARNINGS AND PRECAUTIONS

• This product is not designed to be used by persons (including children)

whose physical, sensorial or mental capacities are reduced, or with lack
of experience or skill, unless suitable instructions regarding use of the
product have been provided by a person responsible for safety.

• The key-operated selector switch must be positioned in sight of the

automation, but far from moving parts and at a height of at least 1.5 m
from the ground, not accessible by the public. If this is used in “hold-to-
run” mode, ensure that there are no persons in the vicinity of the
automation.

• In the vicinity of the automation children must be supervised to ensure

that they do not play with it.

• Ensure that there are not points of entrapment or crushing with fixed

parts when the gate leaf is in the maximum opening or closing position;
protect parts if necessary.

• The product may not be considered an efficient system of protection

against intrusion. If an efficient protection system is required, the
automation must be integrated with other safety devices.

• The automation must not be used before performing the commissioning

procedure as specified in the chapter “Testing and commissioning”.

• Check the automation frequently to ensure there is no imbalance, signs

of wear or damage to electrical or mechanical parts. Do not use the
automation if adjustments or repairs are necessary.

• The product’s packaging materials must be disposed of in full compli-

ance with local regulations.

1.3 - OPERATION WARNINGS

• For cleaning the product surfaces, use a soft damp cloth. Use water

only; never use detergents or solvents for cleaning.

–––  STEP 1  –––

1.1

-

SAFETY WARNINGS

• CAUTION!

– This manual contains important instructions and

warnings for personal safety.

Incorrect installation could cause seri-

ous physical injury. Carefully read all parts of this manual before starting
any work. If in doubt, suspend installation immediately and contact the
Mhouse Technical Assistance.

• CAUTION!

– Important instructions: keep this manual in a safe

place to enable future product maintenance and disposal proce-
dures.

• CAUTION!

– According to the most recent European legislation,

the production of a power-operated door or gate must comply with
the standards envisaged in the Directive 2006/42/EC (Machinery
Directive) and in particular standards EN 12445; EN 12453; EN
12635 and EN 13241-1, which enable declaration of presumed
conformity of the automation. 

In consideration of this, 

all mains

connection, testing, commissioning and maintenance operations
must be performed exclusively by a qualified and skilled techni-
cian!
All preliminary set-up, installation and programming operations
may be performed by personnel with standard skills, provided that
all instructions and the relative sequences in this manual are strict-
ly observed.

1.2 - INSTALLATION WARNINGS

All tasks marked with the symbol alongside
may constitute a hazard source. Therefore
they must be performed exclusively by skilled
and qualified personnel, in observance of the -
se instructions and current safety standards
applicable in the place of use.

• Before installation, ensure that this product is suitable for automation of

your gate or door (see paragraphs 3.1, 3.2 and chapter “Product
Technical Specifications”). If not suitable, do NOT proceed with installa-
tion.

• The automation power line must be equipped with a device for protec-

tion against short circuits and a device for disconnection of the automa-
tion from the power mains (neither device is supplied with the kit).
The disconnect device must have contacts with a sufficient gap to
ensure complete disconnection, in compliance with the overvoltage
category III, according to the installation instructions.

•

All installation and maintenance operations must be performed
with the automation disconnected from the power supply.

If the

power disconnect device is not visible from the location of the automa-
tion, before work a notice should be affixed on the disconnect device,
with the text “CAUTION! MAINTENANCE IN PROGRESS”.

•

CAUTION! - Never power up the motor before fully installed
on the column and leaf of the gate.

• During installation, handle the automation with care, avoiding the risk of

impact, dropping or contact with any type of liquid. Never place the
product near to sources of heat and never expose to naked flames. This
may damage product components and cause malfunctions, fire or haz-
ardous situations. If this occurs, suspend installation immediately and
contact the MhouseTechnical Assistance.

• Never make modifications to any part of the product. Operations other

than as specified can only cause malfunctions. The manufacturer
declines all liability for damage caused by makeshift modifications to the
product.

• If the power cable is damaged, it must be replaced exclusively by a

qualified technician, to avoid potential risks.

• Connect the control unit to an electric power line equipped with an

earthing system.

English

2

– English