Annex 3
USER’S GUIDE
This guide must be stored safely and be accessible to all automation
users.
• Safety instructions
- Keep at a safe distance when the gate is moving; never pass
through the access point until the gate is completely open with the
leafs stationary.
- Do not allow children to play near the gate or with the controls.
- Suspend the use of the automation immediately as soon as you
notice something abnormal in the operation (noises or jolting
movements); failure to follow this warning may cause serious dan-
ger and accidents.
- Never touch any part of the automation while the gate is moving.
- Regular checks must be carried out according to the maintenance
plan.
- Maintenance or repairs must only be carried out by qualified tech-
nical personnel.
• Gate control
––– With radio transmitter –––
The radio transmitter supplied is ready to use. The functions of the four
keys are as follows:
Function
(*)
Key T1
Key T2
Key T3
Key T4
(*) This table must be compiled by the person who programmed the
transmitters.
––– With key–operated selector switch –––
The selector has 2 control positions, with automatic return of the key to
the central position.
ACTION
FUNCTION
Turned right: “OPEN”
(*)
Turned left: “STOP”
Stops gate movement
(*) This table must be compiled by the person who programmed the
control unit.
––– Control with safety devices out of service –––
In the event of safety devices malfunctioning or out of service, the gate
may still be moved.
01.
Activates the gate command (with transmitter or key-operated selec-
tor switch). If the safety devices enable this, the gate will open normal-
ly; otherwise the flashing light emits a number of flashes but the
manoeuvre will not start (the number of flashes depends on the rea-
son for the manoeuvre not starting).
02.
Within 3 seconds activate the command again and keep the key
pressed.
04.
After approx. 2 seconds the gate starts moving in “hold-to-run”
mode, i.e. the gate continues to move while the command is pressed;
the gate stops as soon as the key is released.
In the event of safety devices out of service arrange for repairs to the
automation immediately.
• Manually releasing or locking the gear-
motor
The gearmotor is equipped with a mechanical system that enables manu-
al opening and closing of the gate. These manual operations must be per-
formed in the event of a power failure, malfunctions or during the installa-
tion phases.
Note
- In the event of a power failure, the gate may be powered by the
backup battery PR2, if present on the system.
To release the gearmotor manually, refer to
fig. 39
and proceed as fol-
lows.
01.
Rotate the release disk clockwise through 90°, to expose the re -
lease pin.
02.
Insert the key supplied in the release pin.
03.
Turn the release key clockwise through nearly one complete turn.
04.
The gate leaf can now be moved manually to the required position.
05.
To restore automatic operation, turn the key anticlockwise in the
release pin and manually move the gate until you can hear the leaf
mechanically engage with the drive mechanism.
06.
Then remove the key from the release pine and turn the release disk
anti-clockwise through 90° to cover the hole.
T1
Led
T3
T4
T2
39
Release
Lock
English
English –
41
Summary of Contents for WT1S
