background image

Support 

 

For other RedEdge-MX or Altum associated integration guides, please visit 
our Knowledge Base at support.micasense.com  
 
For additional questions, please contact 

support@micasense.com

 

  
 

 
MicaSense RedEdge-MX & Altum Quick Mount Gen. 2 for DJI Matrice 300 RTK Instructions. 
 
The contents of this manual are subject to change without notice.  
 
MicaSense, Inc. assumes no liability for incidental or consequential damages arising from the 
use of this product, and any claims by a third party.  
 
Copying of the contents of this manual, in whole or in part, as well as the scanner applications 
is prohibited under the copyright law.  
 
 
 
DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY  
 
MICASENSE MAKES NO REPRESENTATION OR WARRANTY, EXPRESS OR IMPLIED, WITH 
RESPECT TO MICASENSE ACCESSORIES. MICASENSE DISCLAIMS ANY LIABILITY FOR 
INDIRECT, CONSEQUENTIAL, PUNITIVE, OR SPECIAL DAMAGES, INCLUDING WITHOUT 
LIMITATION DAMAGES FOR LOST DATA, LOST REVENUE, LOST PROFITS, OR 
REPLACEMENT PRODUCT COSTS ARISING OUT OF THE PURCHASE, USE, OR 
PERFORMANCE OF THE MICASENSE ACCESSORIES, UNDER ANY THEORY OF LIABILITY, 
EVEN IF MICASENSE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 
MICASENSE DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR 
A PARTICULAR PURPOSE, AND DISCLAIMS ANY IMPLIED WARRANTY ARISING FROM A 
COURSE OF PERFORMANCE, DEALING, USAGE, OR TRADE PRACTICE. THE PRICE OF 
PRODUCTS DISTRIBUTED BY MICASENSE OR ITS AUTHORIZED DEALERS REFLECTS THE 
ALLOCATION OF RISK ARISING FROM THE WARRANTY EXCLUSIONS AND THIS 
DISCLAIMER AND LIMITATION OF LIABILITY. 
 
 
 

 
Rev 01 - July 2020 

PAGE 9 

 

 

Summary of Contents for RedEdge-MX DJI M300 RTK Quick Mount Gen. 2














Reviews: