background image

 

Micrel, Inc.  

  1849 Fortune Drive  

  San Jose, CA 95131  

  U.S.A.   

408-955-0800  (voice)  

  408-955-1577  (fax) 

http://www.Micrel.com

 

 

 
 
KSZ8873MLL/FLL/RLL 
Evaluation Board User’s Guide

 

 

KSZ8873MLL/FLL/RLL Integrated 3-Port 10/100 Managed Switch with 
PHYs 
 
Revision 1.1   January 2011 

 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 

 

© Micrel, Inc. 2011 

All rights reserved 

 

Micrel is a registered trademark of Micrel and its subsidiaries in the  

United States and certain other countries.  All other trademarks are the 

property of their respective owners. 

 
 

The information furnished by Micrel in this datasheet is believed to be accurate and reliable.  However, no responsibility is 
assumed  by  Micrel  for  its  use.    Micrel  reserves  the  right  to  change  circuitry  and  specifications  at  any  time  without 
notification  to  the  customer.    Micrel  Products  are  not  designed  or  authorized  for  use  as  components  in  life  support 
appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. 
Life  support  devices  or  systems  are  devices  or  systems  that  (a)  are  intended  for  surgical  implant  into  the  body  or  (b) 
support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user.  
A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own 
risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. 

 

Summary of Contents for KSZ8873FLL











Reviews: