background image

 

Micrel, Inc.  

  2180 Fortune Drive  

  San Jose, CA 95131  

  U.S.A.   

408-944-0800  (voice)  

  408-474-1000  (fax) 

http://www.Micrel.com

 

 

 
 
KSZ9031MNX 

Gigabit Ethernet Transceiver  
with GMII / MII Support 
 
 
KSZ9031MNX-EVAL Board User’s Guide

 

 

 
Revision 1.0  /  August 2012 

 
 
 
 
 

 
 
 
 
 
 
 
 

 

© Micrel, Inc. 2012 

All rights reserved 

 

Micrel is a registered trademark of Micrel and its subsidiaries in the  

United States and certain other countries.  All other trademarks are the 

property of their respective owners. 

 
 

The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is 
assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without 
notification to the customer. Micrel Products are not designed or authorized for use as components in life support 
appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. 
Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) 
support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user.  
A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own 
risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. 

Summary of Contents for KSZ9031MNX
























Reviews: