background image

OM 500 - PARTS LIST

FIG. 7

ITEM

PART NO.

DESCRIPTION

ITEM

PART NO.

DESCRIPTION

1.

34126-01

Cabinet Weldment

15.

P1954

Strain Relief (not shown)

2.

34142-03

Inlet Plenum (3”-8” collars)

16.

34150-01 Control Box Cover

3.

34094-02

Wall Bracket (2 ea. required)

17.

P1372

Door Latch (2 ea. required)

4.

34122-01

Blower/Rivnut Assembly (120 V & 220 V)

18.

34136-01 Filter Access Door

5.

34148-01

Exhaust Panel

19.

P2126

Gasket (specify length required)

6.

P1717

Motor (120 V)

20.

34161-01 Optional Hepa Kit

P1762

Motor (208-230/460 V)

21.

P2250

Optional Magnehelic Gauge

7.

P2064

Belt

          Not Shown

P2061

Oil Impinger

8.

P1789

Motor Pulley

          Not Shown

P2062

Oil Bag Filter

 9.

P1710

Blower Pulley

          Not Shown

P2072

Optional Hepa Filter

10.

34134-01

Front Access Panel

          Not Shown

P2070

Optional Oil Bag Filter

11.

P1429

Lamp (120 V)

 (used with Hepa Filter)

P1481

Lamp (220 V)

          Not Shown

P3001

Optional 2” Max Grid Panel Filter

12.

P1428

Pressure Switch

                          Not Shown

P3008

Optional 4”Mist-Xfilter (Chevron)

13.

P1356

ON/OFF Switch

          Not Shown

34088-02 Optional Ceiling Bracket (2 ea. required)

14.

P1363

Power Cord

          Not Shown

34162-01 Optional Base Assembly

          Not Shown

34145-01 Optional 6” Diameter Collar Adapter

7

OM500

Summary of Contents for OM 500









Reviews: