background image

QD-DVD Series 

 

 

21

Appendix 3: Error Messages 

Master Discs should always be clean and free from scratches to reduce the number of 
duplication failures. 

If an error situation occurs during duplication, the display will show both an error code and an 
error message. 

Error 

Code 

Error Message 

Description and Recommended Solutions 

200 

Source Disc Empty 

The master disc was detected and identified successfully, 
but is blank.   

Check the master to ensure it contains data.

 

201 Bad 

Master 

The master disc is detected but can’t be identified.  

Check the master disc for defects or errors.

 

202 No 

Targets! 

All blank discs are missing once the job has already 
started. 

Verify that blank discs are loaded into the recorders. 

203 

Burner Mixed or 

Firmware Version 

Mixed 

The model or firmware versions of all installed recorders 
are not the same. 

Drive may have been replaced.  Contact Tech 
Support.   

204 

Targets & Master Not 

Compatible! 

The master disc and target discs do not have the same 
format. 

Verify that the master and target discs are the same 
format (CD master and CD blanks, for instance).

  

You 

can use Disc Info in the Utilities menu to verify the disc 
formats.

 

205 

Targets Not Blank! 

Existing data has been detected on the target discs. 

Verify the discs are blank, replace if not. 

206 

Targets & Master Size 

Mismatch! 

During Compare:

 The sizes of the master disc and 

successful copies are different. 

During Copy:

 The capacity of the blank discs is less than 

the data size of the master. 

During Compare:  Contact Tech Support 
During Copy:
 Use Disc Info in the Utilities menu to 
verify that the blanks capacity is large enough for the 
data on the master disc.

 

208 

Targets are not RW 

Discs! 

The target discs are not Rewritable during an Erase 
attempt. 

Verify that each loaded disc is rewritable. 

209 

Master Disc is CSS 

Protected! 

The master disc is copy protected. 

Copy protected masters cannot be duplicated.   

210 Bad 

Discs! 

The target discs are detected but cannot be identified. 

Replace discs that cannot be identified. 

211 

This format can not be 

tested! 

Target discs during a Test attempt are DVD+R, 
DVD+RW, DVD+R DL, BD-R, or BD-RE. 

Disc formats listed above are not supported by the 
test function. 

251 

Copy Audio Error 

Applies to Mix Audio Tracks.

  An error occurred during 

the Mix Audio process.  Could be caused by either a 
master error or a recording error. 

Try a different master or blank disc. 

252 

Not Audio CD 

Applies to Mix Audio Tracks.  

The master disc is not an 

Audio CD. 

Verify the master disc is an Audio CD. 

 

Summary of Contents for QD-DVD























Reviews: