background image

Pin Number

Function

Description

7

NC

Not connected

8

NC

Not connected

Table 4-6. J206 Stacking Connector

Pin Number

Function

Description

20

UART_RTS

Bluetooth

®

 UART RTS output

21

UART_CTS

Bluetooth

®

 UART CTS input

35

GND

Ground

36

GND

Ground

4.2 

ATWILC3000 Shield Raspberry Pi Stacking Connector

The ATWILC3000 Shield contains a Raspberry Pi compatible 40-pin stacking connector used to connect
the board to a Raspberry Pi base board. This is also used for exposing the unused pins to the user. The
pinout definition for the Raspberry Pi connector is given in the following table.

Table 4-7. J207 Stacking Connector

Pin Number

Function

Description

1

VCC_INT_P3V3

3.3V power supply. Insert jumper cap on J300-1 and
J300-2 to use this power supply.

2

NC

Not connected

3

GPIO2/SUSPEND

GPIO signal

4

NC

Not connected

5

CHIP_EN

ATWILC3000 Chip enable is controlled by the host
MCU

6

GND

Ground

7

IRQN

Host interrupt request output

8

UART_RX

Bluetooth

®

 UART receive

9

GND

Ground

10

UART_TX

Bluetooth

®

 UART transmit

11

CTS

Bluetooth

®

 UART CTS input

12

GEN1/RTC_CLK

By default, this pin is not connected. Mount R315 (0Ω)
to connect.

13

SDDATA3

SDIO Data 3. By default, this pin is not connected.
Mount R227 (0Ω) to connect.

14

GND

Ground

 ATWILC3000

Hardware Specifications

©

 2018 Microchip Technology Inc.

 User Guide

DS50002769A-page 9

Summary of Contents for ATWILC3000 Shield




















Reviews: