PIC16C62B/72A
DS35008C-page 84
Preliminary
1998-2013 Microchip Technology Inc.
13.1
DC Characteristics:
PIC16C62B/72A-04 (Commercial, Industrial, Extended)
PIC16C62B/72A-20 (Commercial, Industrial, Extended)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature
0°C
T
A
+70°C
for commercial
-40°C
T
A
+85°C
for industrial
-40°C
T
A
+125°C
for extended
Param
No.
Sym
Characteristic
Min
Typ†
Max
Units
Conditions
D001
D001A
V
DD
Supply Voltage
4.0
4.5
V
BOR
*
-
-
-
5.5
5.5
5.5
V
V
V
XT, RC and LP osc mode
HS osc mode
BOR enabled (Note 7)
D002*
V
DR
RAM Data Retention
Voltage
(Note 1)
-
1.5
-
V
D003
V
POR
V
DD
Start Voltage
to
ensure internal
Power-on Reset signal
-
V
SS
-
V
See section on Power-on Reset for details
D004*
D004A*
S
VDD
V
DD
Rise Rate
to
ensure internal
Power-on Reset signal
0.05
TBD
-
-
-
-
V/ms PWRT enabled (PWRTE bit clear)
PWRT disabled (PWRTE bit set)
See section on Power-on Reset for details
D005
V
BOR
Brown-out Reset
voltage trip point
3.65
-
4.35
V
BODEN bit set
D010
D013
I
DD
Supply Current
(Note 2, 5)
-
-
2.7
10
5
20
mA
mA
XT, RC osc modes
F
OSC
= 4 MHz, V
DD
= 5.5V (Note 4)
HS osc mode
F
OSC
= 20 MHz, V
DD
= 5.5V
D020
D021
D021B
I
PD
Power-down Current
(Note 3, 5)
-
-
-
-
10.5
1.5
1.5
2.5
42
16
19
19
A
A
A
A
V
DD
= 4.0V, WDT enabled,-40
C to +85
C
V
DD
= 4.0V, WDT disabled, 0
C to +70
C
V
DD
= 4.0V, WDT disabled,-40
C to +85
C
V
DD
= 4.0V, WDT disabled,-40
C to +125
C
D022*
D022A*
I
WDT
I
BOR
Module Differential
Current (Note 6)
Watchdog Timer
Brown-out Reset
-
-
6.0
TBD
20
200
A
A
WDTE
BIT
SET
, V
DD
= 4.0V
BODEN bit set, V
DD
= 5.0V
* These parameters are characterized but not tested.
† Data in "Typ" column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1:
This is the limit to which V
DD
can be lowered without losing RAM data.
2:
The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all I
DD
measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to V
DD
,
MCLR = V
DD
; WDT enabled/disabled as specified.
3:
The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
DD
and V
SS
.
4:
For RC osc mode, current through Rext is not included. The current through the resistor can be estimated by
the formula Ir = V
DD
/2Rext (mA) with Rext in kOhm.
5:
Timer1 oscillator (when enabled) adds approximately 20
A to the specification. This value is from charac-
terization and is for design guidance only. This is not tested.
6:
The
current is the additional current consumed when this peripheral is enabled. This current should be
added to the base I
DD
or I
PD
measurement.
7:
This is the voltage where the device enters the Brown-out Reset. When BOR is enabled, the device will
perform a brown-out reset when V
DD
falls below V
BOR
.
Summary of Contents for PIC16C62B/72A
