manualshive.com logo in svg

Microchip Technology PIC24FV16KM204 FAMILY, Datasheet

The Microchip Technology PIC24FV16KM204 FAMILY offers exceptional performance and versatility for various industrial applications. Access its comprehensive Datasheet and user manual for a deeper understanding of this product's capabilities. Easily download these resources for free from 88.208.23.73:8080, empowering you with all the necessary technical information to maximize your experience with this advanced technology.

Share
Download
background image

PIC24FV16KM204 FAMILY

DS33030A-page 212

Advance Information

 2013 Microchip Technology Inc.

19.1

A/D Control Registers

The 12-bit A/D Converter module uses up to
43 registers for its operation. All registers are mapped
in the data memory space.

19.1.1

CONTROL REGISTERS

Depending on the specific device, the module has up to
eleven control and status registers:
• AD1CON1: A/D Control Register 1
• AD1CON2: A/D Control Register 2
• AD1CON3: A/D Control Register 3
• AD1CON5: A/D Control Register 5
• AD1CHS: A/D Sample Select Register
• AD1CHITH and AD1CHITL: A/D Scan Compare 

Hit Registers

• AD1CSSH and AD1CSSL: A/D Input Scan Select 

Registers

• AD1CTMENH and AD1CTMENL: CTMU Enable 

Registers

The AD1CON1, AD1CON2 and AD1CON3 registers
(

Register 19-1

, 

Register 19-2

 and 

Register 19-3

)

control the overall operation of the A/D module. This
includes enabling the module, configuring the
conversion clock and voltage reference sources,
selecting the sampling and conversion Triggers, and
manually controlling the sample/convert sequences.
The AD1CON5 register (

Register 19-4

) specifically

controls features of the Threshold Detect operation,
including its function in power-saving modes.
The AD1CHS register (

Register 19-5

) selects the input

channels to be connected to the S/H amplifier. It also
allows the choice of input multiplexers and the
selection of a reference source for differential
sampling. 

The AD1CHITH and AD1CHITL registers
(

Register 19-6

 and 

Register 19-7

) are semaphore

registers used with Threshold Detect operations. The
status of individual bits, or bit pairs in some cases,
indicates if a match condition has occurred. AD1CHITL
is always implemented, whereas AD1CHITH may not
be implemented in devices with 16 or fewer channels.
The AD1CSSH/L registers (

Register 19-8

 and

Register 19-9

) select the channels to be included for

sequential scanning.
The AD1CTMENH/L registers (

Register 19-10

 and

Register 19-11

) select the channel(s) to be used by the

CTMU during conversions. Selecting a particular
channel allows the A/D Converter to control the CTMU
(particularly, its current source) and read its data
through that channel. AD1CTMENL is always
implemented, whereas AD1CTMENH may not be
implemented in devices with 16 or fewer channels.

19.1.2

A/D RESULT BUFFERS

The module incorporates a multi-word, dual port buffer,
called ADC1BUFn. Each of the locations is mapped
into the data memory space and is separately
addressable. The buffer locations are referred to as
ADC1BUF0 through ADC1BUFn (up to 17). 
The A/D result buffers are both readable and writable.
When the module is active (AD1CON<15> = 

1

), the

buffers are read-only and store the results of A/D
conversions. When the module is inactive
(AD1CON<15> = 

0

), the buffers are both readable and

writable. In this state, writing to a buffer location
programs a conversion threshold for Threshold Detect
operations. 
Buffer contents are not cleared when the module is
deactivated with the ADON bit (AD1CON1<15>).
Conversion results and any programmed threshold
values are maintained when ADON is set or cleared.

Summary of Contents for PIC24FV16KM204 FAMILY

















































































































































































































































































































































Reviews:

No comments

Related manuals for PIC24FV16KM204 FAMILY

ABB HF Series Manual preview
HF Series
Brand: ABB Pages: 63
hager coviva Smartbox TKP100A Configuration Manual preview
coviva Smartbox TKP100A
Brand: hager Pages: 45
Lattice Semiconductor MachXO5-NX Development Kit Quick Start preview
MachXO5-NX Development Kit
Brand: Lattice Semiconductor Pages: 2
CELSYS Clip Studio TABMATE Instructions preview
Clip Studio TABMATE
Brand: CELSYS Pages: 2
MRMC MIMIC HRNDWHEELS Quick Start Manual preview
MIMIC HRNDWHEELS
Brand: MRMC Pages: 20
Greenheck MP-220A Installation, Operation And Maintenance Manual preview
MP-220A
Brand: Greenheck Pages: 4
Watlow Ramping and Profiling Microprocessor-Based Control SERIES 1500 User Manual preview
Ramping and Profiling Microprocessor-Based Control SERIES 1500
Brand: Watlow Pages: 90
jbc KNE Instruction Manual preview
KNE
Brand: jbc Pages: 8
Active-semi ACT4910EVK1-121 User Manual preview
ACT4910EVK1-121
Brand: Active-semi Pages: 15
Geco GH10HA User Manual preview
GH10HA
Brand: Geco Pages: 20
Abelko UltraBase20 User Manual preview
UltraBase20
Brand: Abelko Pages: 70
BIFFI ALGAS-MHP Installation, Operation And Maintenance Manual preview
ALGAS-MHP
Brand: BIFFI Pages: 56
Zennio MINiBOX 0-10V X1 User Manual preview
MINiBOX 0-10V X1
Brand: Zennio Pages: 25
Spektrum VR6010 Instructions preview
VR6010
Brand: Spektrum Pages: 2
ARZAMAN SmartPID BBQ Easy User Manual preview
SmartPID BBQ Easy
Brand: ARZAMAN Pages: 27
DMC 3I09S0100001 User Manual preview
3I09S0100001
Brand: DMC Pages: 12
Dabir Surfaces C2-100 Series Quick Setup Manual preview
C2-100 Series
Brand: Dabir Surfaces Pages: 2
KEB COMBIVERT 10F6 Series Instructions For Use Manual preview
COMBIVERT 10F6 Series
Brand: KEB Pages: 84

Brands by name

Popular brands

Load more brands