manualshive.com logo in svg

Microchip Technology PIC24FV16KM204 FAMILY, Datasheet

The Microchip Technology PIC24FV16KM204 FAMILY offers exceptional performance and versatility for various industrial applications. Access its comprehensive Datasheet and user manual for a deeper understanding of this product's capabilities. Easily download these resources for free from 88.208.23.73:8080, empowering you with all the necessary technical information to maximize your experience with this advanced technology.

Share
Download
background image

 2013 Microchip Technology Inc.

Advance Information

DS33030A-page 175

PIC24FV16KM204 FAMILY

15.2

Transmitting in 8-Bit Data Mode

1.

Set up the UARTx:
a)

Write the appropriate values for data, parity
and Stop bits.

b)

Write the appropriate baud rate value to the
UxBRG register.

c)

Set up transmit and receive interrupt enable
and priority bits.

2.

Enable the UARTx.

3.

Set the UTXEN bit (causes a transmit interrupt,
two cycles after being set).

4.

Write the data byte to the lower byte of the
UxTXREG word. The value will be immediately
transferred to the Transmit Shift Register (TSR)
and the serial bit stream will start shifting out
with the next rising edge of the baud clock.

5.

Alternately, the data byte may be transferred
while UTXEN = 

0

, and then, the user may set

UTXEN. This will cause the serial bit stream to
begin immediately, because the baud clock will
start from a cleared state.

6.

A transmit interrupt will be generated as per
interrupt control bit, UTXISELx.

15.3

Transmitting in 9-Bit Data Mode

1.

Set up the UARTx (as described in 

Section 15.2

“Transmitting in 8-Bit Data Mode”

).

2.

Enable the UARTx.

3.

Set the UTXEN bit (causes a transmit interrupt,
two cycles after being set).

4.

Write UxTXREG as a 16-bit value only.

5.

A word write to UxTXREG triggers the transfer
of the 9-bit data to the TSR. The serial bit stream
will start shifting out with the first rising edge of
the baud clock.

6.

A transmit interrupt will be generated as per the
setting of control bit, UTXISELx.

15.4

Break and Sync Transmit 
Sequence

The following sequence will send a message frame
header, made up of a Break, followed by an Auto-Baud
Sync byte.
1.

Configure the UARTx for the desired mode.

2.

Set UTXEN and UTXBRK – this sets up the
Break character.

3.

Load the UxTXREG with a dummy character to
initiate transmission (value is ignored).

4.

Write ‘55h’ to UxTXREG – loads the Sync
character into the transmit FIFO.

5.

After the Break has been sent, the UTXBRK bit
is reset by hardware. The Sync character now
transmits.

15.5

Receiving in 8-Bit or 9-Bit Data 
Mode

1.

Set up the UARTx (as described in 

Section 15.2

“Transmitting in 8-Bit Data Mode”

).

2.

Enable the UARTx.

3.

A receive interrupt will be generated when one
or more data characters have been received, as
per interrupt control bit, URXISELx.

4.

Read the OERR bit to determine if an overrun
error has occurred. The OERR bit must be reset
in software.

5.

Read UxRXREG.

The act of reading the UxRXREG character will move
the next character to the top of the receive FIFO,
including a new set of PERR and FERR values.

15.6

Operation of UxCTS and UxRTS 
Control Pins

UARTx Clear-to-Send (UxCTS) and Request-to-Send
(UxRTS) are the two hardware controlled pins that are
associated with the UARTx module. These two pins
allow the UARTx to operate in Simplex and Flow Con-
trol modes. They are implemented to control the
transmission and reception between the Data Terminal
Equipment (DTE). The UEN<1:0> bits in the UxMODE
register configure these pins.

15.7

Infrared Support

The UARTx module provides two types of infrared
UARTx support: one is the IrDA clock output to support
an external IrDA encoder and decoder device (legacy
module support), and the other is the full implementation
of the IrDA encoder and decoder. 
As the IrDA modes require a 16x baud clock, they will
only work when the BRGH bit (UxMODE<3>) is ‘

0

’.

15.7.1

EXTERNAL IrDA SUPPORT – IrDA 
CLOCK OUTPUT

To support external IrDA encoder and decoder devices,
the UxBCLK pin (same as the UxRTS pin) can be
configured to generate the 16x baud clock. When
UEN<1:0> = 

11

, the UxBCLK pin will output the 16x

baud clock if the UARTx module is enabled; it can be
used to support the IrDA codec chip.

15.7.2

BUILT-IN IrDA ENCODER AND 
DECODER

The UARTx has full implementation of the IrDA
encoder and decoder as part of the UARTx module.
The built-in IrDA encoder and decoder functionality is
enabled using the IREN bit (UxMODE<12>). When
enabled (IREN = 

1

), the receive pin (UxRX) acts as the

input from the infrared receiver. The transmit pin
(UxTX) acts as the output to the infrared transmitter.

Summary of Contents for PIC24FV16KM204 FAMILY

















































































































































































































































































































































Reviews:

No comments

Related manuals for PIC24FV16KM204 FAMILY

Vacon NX series Maintenance Manual preview
NX series
Brand: Vacon Pages: 64
Paoli F1 Operating And Maintenance Manual preview
F1
Brand: Paoli Pages: 16
Panasonic FP2 Series Technical Manual preview
FP2 Series
Brand: Panasonic Pages: 68
Panasonic FP0H Series Operation Manual preview
FP0H Series
Brand: Panasonic Pages: 20
Value Point 3500 Quick Start Manual preview
3500
Brand: Value Point Pages: 7
QCON ProX Setup preview
ProX
Brand: QCON Pages: 4
GCE S 400 Operating Instructions Manual preview
S 400
Brand: GCE Pages: 24
RadioMaster POCKET Quick Start Manual preview
POCKET
Brand: RadioMaster Pages: 10
Maestra 8080 User Manual preview
8080
Brand: Maestra Pages: 22
Rain Bird PAR+ES Installation Manual preview
PAR+ES
Brand: Rain Bird Pages: 24
Rain Bird ESP-LXIVM Series Device Installation Manuallines preview
ESP-LXIVM Series
Brand: Rain Bird Pages: 16
Wang 2236 Product/Maintenance Manual preview
2236
Brand: Wang Pages: 68
NAVITAS TSE Series Installation Manual preview
TSE Series
Brand: NAVITAS Pages: 14
V2 STARK6 Quick Start Manual preview
STARK6
Brand: V2 Pages: 12
H3C WBC580 G2 Installation, Quick Start preview
WBC580 G2
Brand: H3C Pages: 5
z21 XL BOOSTER Quick Start Manual preview
XL BOOSTER
Brand: z21 Pages: 2
ZKTeco IN710 Quick Start Manual preview
IN710
Brand: ZKTeco Pages: 11
Securi-Prod LK190 Installation Manual preview
LK190
Brand: Securi-Prod Pages: 3

Brands by name

Popular brands

Load more brands