background image

9

SYSTEM ENTRY TIME

Entry time is the period
of time allowed for you
to enter and disarm
the system with the
password (factory set
to 1122), before the
sirens sound. 
The entry time is set by
the factory to 20
seconds but this can
be changed to a
choice of 7 other entry
times to suit you. 

If for any reason the
sirens sound, p

prre

essss

11112

22

2  to disarm.

Then P

Prre

essss  P

P  2

2  EE  and within 5

seconds your choice.
((IIff  yyo

ou

u  d

do

o  n

no

ott  d

de

ecciid

de

e  w

wiitth

hiin

n  5

5

sse

ecco

on

nd

dss,,  tth

hrre

ee

e  ssh

ho

orrtt  b

blle

ee

ep

pss

w

wiillll  b

be

e  h

he

ea

arrd

d,,  a

an

nd

d  yyo

ou

u  w

wiillll

h

ha

avve

e  tto

o  e

en

ntte

err  P

P  2

2  EE  a

an

nd

d  sstta

arrtt

a

ag

ga

aiin

n..))

Then P

Prre

essss  P

P  0

0  EE  to exit

programming. 

1

2

3

4

P

Prre

essss  3

3  EE which is the

program for 40 seconds.
If entered correctly, a
continuous bleep will be
heard for 2 seconds. 

For example, to change the
entry time to 40 seconds (see
choices in Table): 
P

Prre

essss  P

P  11112

22

2  EE  tto

o  e

en

ntte

err

p

prro

og

grra

am

mm

miin

ng

g..

Example:

Exit time is the period
of time allowed for you
to exit after arming the
system with the
password, before the
sirens sound. 
The exit time is set by
the factory to 15
seconds but this can
be changed to a
choice of 7 other exit
times to suit you. 

If for any reason the
sirens sound, p

prre

essss

11112

22

2  to disarm.

SYSTEM EXIT TIME

1

For example, to change the
exit time to 60 seconds (see
choices in Table): 
P

Prre

essss  P

P  11112

22

2  EE  tto

o  e

en

ntte

err

p

prro

og

grra

am

mm

miin

ng

g..

Then P

Prre

essss  P

P  3

3  EE  and within 5

seconds your choice.
((IIff  yyo

ou

u  d

do

o  n

no

ott  d

de

ecciid

de

e  w

wiitth

hiin

n  5

5

sse

ecco

on

nd

dss,,  tth

hrre

ee

e  ssh

ho

orrtt  b

blle

ee

ep

pss

w

wiillll  b

be

e  h

he

ea

arrd

d,,  a

an

nd

d  yyo

ou

u  w

wiillll

h

ha

avve

e  tto

o  e

en

ntte

err  P

P  3

3  EE  a

ag

ga

aiin

n..))

2

3

P

Prre

essss  4

4  EE   which is the

program for 60 seconds.
If entered correctly, a
continuous bleep will be
heard for 2 seconds.

Then P

Prre

essss  P

P  0

0  EE  to exit

programming. 

4

Example:

Choices are:
11EE

10 seconds

0

0EE

15 seconds

2

2EE

20 seconds

3

3EE

40 seconds

4

4EE

60 seconds

5

5EE

90 seconds

6

6EE

120 seconds

77EE

240 seconds

To choose other exit times:
11EE

10 seconds

0

0EE

15 seconds

2

2EE

20 seconds

3

3EE

40 seconds

4

4EE

60 seconds

5

5EE

90 seconds

6

6EE

120 seconds

77EE

240 seconds

www.ukpanels.com

Summary of Contents for MM23207













Reviews: