micronit microfludics FLUIDIC CONNECT 4515 User Manual Download

Page: 3 / 19

CONTENTS

INTRODUCTION................................................................................................................

ASSEMBLY AND ADJUSTMENTS...........................................................................................

2.1 Step 1: Parts Check.......................................................................

2.2 Step 2: Chip Placement.................................................................

2.3 Step 3: Placing the Alignment Nuts...................................................

2.4 Step 4: Connection of Fittings.........................................................

FRAME............................................................................................................................

QUESTIONS AND ANSWERS................................................................................................

TIPS AND TRICKS FOR CONNECTION....................................................................................

5.1 Tightening force..........................................................................

5.2 Stainless Steel / Teflon Connection Kit...............................................

SPECIFICATIONS..........................................................................................................

PARTS LIST....................................................................................................................

Fluidic Connect 4515 - User Manual V1.5

Summary of Contents for FLUIDIC CONNECT 4515




















Search results

Summary of Contents for FLUIDIC CONNECT 4515

Reviews:

Related manuals for FLUIDIC CONNECT 4515

Brands by name

Popular brands

micronit microfludics FLUIDIC CONNECT 4515, User Manual

Search results

Summary of Contents for FLUIDIC CONNECT 4515

Reviews:

Related manuals for FLUIDIC CONNECT 4515

Brands by name

Popular brands