Micros MBB-10 User Manual Download | Manualshive

Page: 1 / 15

background image

MD0011-014

Revision A

Page 1 of 15

The MICROS Bump Bar

MBB-10 and MBB-20 User’s Guide

This document describes the MBB features, shows how to adjust the speaker
and LED from the keypad, as well as determine the firmware version and how
to update if required. Other sections describe how to open the unit and
configure the MBB circuit board configuration switches, and to service the
unit.

Introducing the MICROS Bump Bar ...........................................................2
Adjusting the LED and Speaker from the Keypad ......................................4
MBB Spare Parts .........................................................................................5
Opening the Micros Bump Bar ....................................................................8
Specification Summary..............................................................................13
MBB-10 Bracket Dimensional Drawing ...................................................14
MBB-20 Bracket Dimensional Drawing ...................................................15

1
2
3
...
»

Summary of Contents for MBB-10
















Reviews:

No comments

Related manuals for MBB-10

Brand: UnionSpecial Pages: 56

Tetrix 351 AC/DC Smart FW

Brand: EWM Pages: 117

Brand: HAMAR LASER Pages: 49

Brand: Backyard Discovery Pages: 51

Brand: Nautilus Pages: 12

Brand: CAIRE Pages: 16

Brand: Bacharach Pages: 48

Brand: Tabi Pages: 8

Brand: Dabi Atlante Pages: 102

Brand: E-Z DRILL Pages: 12

Brand: e-survey Pages: 54

Brand: E-Pill Pages: 8

XL-7 Command Station

Brand: E-Mu Pages: 22

Brand: Taylor-Wharton Pages: 25

Brand: i-CAT Pages: 96

Brand: Parkside Pages: 2

Brand: Park House Healthcare Pages: 12

Brand: quadient Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands