To Program Or Edit Dual Watch Location 2 And
Engage Dual Watch Mode:
1. Press the MODE button until the Dual
Watch icon and the channel number
flash on the display.
2. Choose one of the following:
a. Select or edit a channel/privacy
code:
1) Press the CHANNEL UP or
CHANNEL DOWN button to select
a channel (1 to 8).
2) Press the MODE button to set the
channel. The CTCSS icon and
current setting (the small
numbers next to the channel
number or Off) will flash on the
display.
3) Press the CHANNEL UP or
CHANNEL DOWN button to select
a CTCSS privacy code
(00 to 38).
b. Select or edit a channel/DCS code:
1) Press the CHANNEL UP or
CHANNEL DOWN button to select
a channel (1 to 8).
2) Press the MODE button to set the
channel. The CTCSS icon and current setting (the small
numbers next to the channel number or Off) will flash
on the display.
3) Press the MODE button again. The DCS icon and
current setting (the small numbers next to the channel
number or Off) will flash on the display.
4) Press the CHANNEL UP or CHANNEL DOWN button to
select a DCS code (00 to 83).
3. Press the ENTER button to set Dual Watch Location 2 and
engage DUAL WATCH MODE (see below for further details).
NOTES: To terminate Dual Watch and proceed to the next
available Mode Function, press the MODE button.
While setting Dual Watch Location 2, if you do not
press any buttons for fifteen (15) seconds your radio
will automatically return to LISTENING MODE on Dual
During An Incoming Transmission, You Can Choose
From The Following:
a. Press and hold the TALK button to communicate on that
memory location. Your radio will remain on that memory
location and return to LISTENING MODE.
b. Press the CHANNEL UP or CHANNEL DOWN button to
resume scanning memory locations.
If you press the TALK button while scanning and not within ten
(10) seconds of receiving a transmission, you will transmit on
the memory location on which, during scanning, you last
received a transmission. This will return the radio to LISTENING
MODE.
If you do not press any button within ten (10) seconds, your
radio will automatically resume scanning memory locations.
During Scanning (while not receiving a
transmission), You Can Choose From The Following:
a. Press and hold the TALK button to communicate on either
the channel/privacy code or channel/DCS code that was
displayed before you entered Mode Functions or memory
location on which, during scanning, you last received a
transmission. This will return the radio to LISTENING
MODE.
b. Press the MODE button to proceed to other functions.
c. Press the ENTER button to return to LISTENING MODE on
either the channel/privacy code or channel/DCS code
that was displayed before you entered Mode Functions or
the memory location on which, during scanning, you last
received a transmission.
To reduce the number of memory locations being scanned, you
may “un-program” any unwanted locations (see “10 Memory
Locations” for further details).
VibrAlert
®
and Call Tones
Your microTALK
®
radio can alert you to incoming signals by
sounding an audible call tone, by vibrating silently, or both.
To Change Call Settings:
1. Press the MODE button until the Call
Setting icon flashes on the display. The
current setting (“01” – V
Ring, “02” – Vibrate Only, or “00” –
Ring Only) is
displayed.
MODE FUNCTIONS OPERATION
English
2. Press the
CHANNEL UP
or CHANNEL DOWN button
to change the call setting.
3. When your desired call setting is
displayed, choose one of the following:
a. Press the MODE button to enter the
setting and proceed to other functions.
b. Press the ENTER button to enter the setting and return to
LISTENING MODE.
c. Do not press any buttons for fifteen (15) seconds to
enter the setting and return to LISTENING MODE.
Dual Watch
Dual watch allows you to simultaneously
monitor any two (2) Dual Watch Locations.
Dual Watch Location 1 – is always the
channel/privacy code or
channel/DCS code displayed before you entered Mode
Functions. See “CTCSS Privacy Codes” and “DCS
Codes” sections for further details.
Dual Watch Location 2 – will be stored in the radio. It can
be edited and/or recalled for future engagements of
Dual Watch Mode.
Watch Location 1.
To Turn Dual Watch On:
NOTE: Dual Watch Location 2 must be programmed to turn Dual
Watch on.
1. Select the first channel/privacy code or
channel/DCS Code you wish to
monitor (see “CTCSS Privacy Codes”
and “DCS Codes” for further details).
2. Press the MODE button until the Dual
Watch icon and the channel number
flash on the display.
NOTE: While setting Dual Watch, if you do
not press any buttons for fifteen
(15) seconds your radio will
automatically return to LISTENING
MODE on the channel/privacy code
or channel/DCS code displayed
before you entered Mode Functions.
3. Press the ENTER button to engage
DUAL WATCH MODE.
During An Incoming Transmission, You Can Choose
From The Following:
a. Press and hold the TALK button to communicate on that
Dual Watch Location. Your radio will remain on that Dual
Watch Location and return to LISTENING MODE.
b. Press the CHANNEL UP or CHANNEL DOWN button to
resume Dual Watch.
If you press the TALK button while in Dual Watch and not within
ten (10) seconds of receiving a transmission, you will transmit
on the last Dual Watch Location on which you received a
transmission. This will return the radio to LISTENING MODE.
If you do not press any button within ten (10) seconds, your
radio will automatically resume Dual Watch.
Dual Watch Icon
Channel Buttons
Mode Button
Mode Button
Enter Button
Select Channel
Channel Buttons
Mode Button
Select Channel
Select Privacy Code
Select DCS Code
Call Alert Icon
VibrAlert
®
Icon
VibrAlert
®
&
Call Alert Icon
