Microtek MiniLink Operation Manual Download

Page: 4 / 25

NDEX

SECTION

PAGE #

IMPORTANT SAFETY INSTRUCTIONS, FCC NOTICE ---------------- ( i )

RADIO FREQUENCY EXPOSURE, INDUSTRY CANADA ------------- ( ii )

QUICK START GUIDE ----------------------------------------------------------- 2

PRE-INSTALLATION REMINDER, RETURN POLICY ----------------- 3

WEM DESCRIPTION

------------------------------------------------------------- 4

FRONT, REAR & SIDE VIEWS -------------------------------------------------- 4 - 5

PIM DESCRIPTION --------------------------------------------------------------- 5

TOP, RIGHT & LEFT SIDE VIEWS ---------------------------------------------- 5

WES CONNECTION DIAGRAM

----------------------------------------------- 6

WEM INSTALLATION & OPERATION ------------------------------------- 6 - 8

SELECT CHANNEL & POLARITY SELECT ---------------------------------- 6

MOUNT WEM & CONFIGURE CABLE ---------------------------------------- 7

CONNECT WEM & ESTABLISH LINK ---------------------------------------- 8

ADVANCED OPERATION ------------------------------------------------------ 8 - 15

WEB BROWSER INTERFACE --------------------------------------------------- 8

STATIONS/APs ----------------------------------------------------------------------- 12

WIRELESS & SECURITY ----------------------------------------------------------- 13

SECURITY ---------------------------------------------------------------------------- 14

ADMINISTRATION ----------------------------------------------------------------- 15 – 16

SYSTEM INSTALLAION NOTES ------------------------------------------------ 17

WEM SPECIFICATIONS -------------------------------------------------------- 18 - 19

TROUBLE SHOOTING ----------------------------------------------------------- 20

FAQ------------------------------------------------------------------------------------- 21

WARRANTY ------------------------------------------------------------------------- 22

OVERED

RODUCTS

ART

# D

ESCRIPTION

ML WAP

MiniLink 5.3 & 5.8 GHz Wireless Host / Access Point - Directional

ML WAPOM

MiniLink 5.3 & 5.8 GHz Wireless Host / Access Point - Omni-directional

ML WSUOM

MiniLink 5.3 & 5.8 GHz Wireless Client / Subscriber Unit - Omni

ML WSU

MiniLink 5.3 & 5.8 GHz Wireless Client / Subscriber Unit - Standard

ML WSUP

MiniLink 5.3 & 5.8 GHz Wireless Client / Subscriber Unit - Patch

ML WSUDI

MiniLink 5.3 & 5.8 GHz Wireless Client / Subscriber Unit - Dish

ML WEM

MiniLink 5.3 & 5.8 GHz Wireless Ethernet Module

ML WEMP

MiniLink 5.3 & 5.8 GHz Wireless Ethernet Module w/ 6” patch antenna

ML WEM-30

MiniLink 5.8 GHz Wireless Ethernet Module - 30 mile system

*In this manual, WEM refers to all Point-to-Point, Host/Access Point and
Client/Subscriber Unit devices as described in the covered products table above.

- 1 -

Summary of Contents for MiniLink


























Search results

Summary of Contents for MiniLink

Reviews:

Related manuals for MiniLink

Brands by name

Popular brands

Microtek MiniLink, Operation Manual

Search results

Summary of Contents for MiniLink

Reviews:

Related manuals for MiniLink

Brands by name

Popular brands