13.
I n o r d e r t o r e b o o t .
on your CRT.
Y o u s h o u l d g e t t h e f o l l o w i n g m e s s a g e
SOURCE DRIVE NAME (OR RETURN
TO SKIP)
Now press <RETURN>.
D i s p l a y i n g f o l l o w i n g .
DESTINATION DRIVE NAME
(OR RETURN TO
REBOOT)
Press <RETURN>
to reboot.
You will
g e t
p r o m p t ‘ A > ‘ .
Note 1
Important:
At
first you should ‘FORMAT’ a new diskette then
p r o c e e d f o r ‘FSYSGEN’ the same.
When
using
disk drives and
diskettes, the process of
'FSYSGEN' is
not required. Therefore
you should
not
'FSYSGEN' 8"
diskettes, just
'FORMAT'
and start
u s i n g t h e m a c c o r d i n g t o y o u r c h o i c e .
Note 2
I f y o u i n t e n d t o c o n t i n u e ‘FSYSGEN’ more diskette,
j u s t u n l o c k D r i v e
and insert
again a
new
p r e v i o u s l y f o r m a t t e d d i s k e t t e l o c k , a n d f o l l o w
o u r i n s t r u c t i o n f r o m 4 .
SYSTEM : Command for system generation
T h e o b j e c t o f ‘SYSTEM’ is to
‘CCP’, ‘BDOS’,
'BIOS'
into
the system
tracks of the destination
disk
drive diskette.
W h i l e e x e c u t i n g t h i s
'SYSTEM' command program, you should note
that the directory of the diskette never
gets damage.
T h e o p e r a t i o n s a r e a s f o l l o w s .
A>SYSTEM
<RETURN>
V e r s . 2 . 2 S y s t e m g e n e r a t i o n ( f o r F o r m u l a - l )
Destinat’ion drive
name
(or RETURN to reboot):
In the above state,
i n s e r t a n e w d i s k e t t e i n t o o t h e r d r i v e
a n d l o c k .
Now, input the name
of the disk drive in which
have
inserted the new.diskette
and press
<RETURN>..
Due 5.25“ diskettes
being
loaded
by IPL, therefore we only
need
to
do ‘SYSTEM’ of
5.25" diskettes
and not 8”
diskettes.
A c c o r d i n g l y , y o u s h o u l d h a v e t o c h o o s e o n e o f t h e d i s k d r i v e s
n a m e f r o m t h e f o l l o w i n g
'A,B,C,D'
in order to use.
After you input the disk drive’s name,
the following
message will appear on your
CRT.
G e n e r a t i o n S t a r t ( Y / N )
If you intend to generate the 'SYSTEM' on the diskette,
press
then
generation start automatically.
If the
process
completes correctly, the following message
will
a p p e a r o n y o u r C R T , a s ‘ P r o c e s s c o m p l e t e ’ a n d r e t u r n t o i n i t i a l
s t a t e .
I f t h e r e b e i n g a n e r r o r , t h e e r r o r m e s s a g e w i l l a p p e a r o n
your CRT as ‘ D i s k w r i t e e r r o r
and return to initial state.
W h e n y o u d o n o t i n t e n d t o u s e t h i s p r o g r a m o f s y s t e m
g e n e r a t i o n , p r e s s
‘ N ’ ,
the execution stops and returns back to
Operating System.
P r o c e s s c o m p l e t e - - - - - - - - - - - -
( D i s k w r i t e e r r o r I ! ! ) - - - - - - A b n o r m a l
e n d
We have shown
the
procedure
of 'SYSTEM'
a new
diskette
on
the following page.