background image

5 |  

 

 

Settings 

DATE AND TIME SETTING  

Press the wheel in the requested temperature display mode – the lighting will switch on. During 
a time period of the lighting press the wheel one more time. (In case the lighting function is not 
permitted on your device, press the wheel only once.) 

The accurate time will be shown on the display by big numerals. By wheel revolution set hour 
and then by pressing it confirm the setting. The setting of minutes, day, month, year and date is 
done in a similar way.  

After conforming the year by pressing the wheel you will return to the requested humidity display 
mode. 

SCREEN SAVER 

After a certain time of inactivity the measuring unit turns off the display due to the batteries´ 
energy saving. Meanwhile the measuring and control functions stay active. If the screen saver is 
active, there will be an arrow showing  towards the wheel  displayed  for a short time  and  in 
regular intervals, or the indicator located under the display blinks - depending on the set device 
parameters. 

It is possible to return to the basic state anytime by pressing the wheel. 

The screen saver function is activated only in case of permitting in the device settings.  

BATTERY CHANGE 

The device will signalize a need of battery change by showing a discharged battery icon in the 
upper part of the screen. In case the screen saver is switched on, this icon will blink 
simultaneously with the arrow in the left part of the display or the indicator light of the saver will 
blink twice.  

Batteries – two alkaline pencilling batteries AA are accessible after the plastic cover removing.  

Carefully remove the control wheel with a small, thin object (i.e. with a knife) in a following way: 

Insert the knife under the wheel from the right hand side and then pull it toward yourself gently. 

Grasp the plastic cover and by pulling the bottom part release it and then remove it.  Change 
the batteries by paying attention at the right polarity. Mount the cover. After the change set the 
accurate time and date.  

It is recommended to use lithium AA  ,,Energizer Ultimate Lithium´´ batteries  (sometimes 
labelled as Energizer L91). These batteries last longer in comparison with the usual alkaline 
batteries AA. The batteries are not accessible from another manufacturers, as Energizer 
company has got a patent at its technology.  

 Lithium batteris Energizer Ulitimate Lithium

 

Summary of Contents for Dry Precision 100
















Reviews: