background image

8

installation manual

11    TRIAL RUN

Please conduct in accordance with “Trial Run Tenor Nameplate” 

on the electric control box. 

Perform trial run only after all installations are finished.

Confirm the following issues before trial operation, and        the 

box for the confirmed items.

Perform the trial run only after the outdoor unit has been 

powered on for over 12 hours. 

Check that all valves are opened before trial run.

Check the electric safety before trial run. 

Do not perform compulsory operation in any way.(It is very 

dangerous if the protection device is not active)

Check whether the indoor unit and the outdoor are 

installed properly.

Check whether the piping and wiring are correct.

Check whether the refrigerant pipeline system is 

inspected for leakage.

Check whether the drain is smooth.

Check whether the heat insulation is perfect.

Check whether the ground cables are connected 

correctly.

Check whether the pipe length and the refrigerant 

amount are recorded.

Check whether the supply voltage is equal to the rated 

voltage of the air conditioner.

Check whether any obstacles exist at the air 

inlet/outlet of the indoor or outdoor unit.

Open the gas valve and the liquid valve.

Connect the power supply to preheat the air 

conditioner.

CAUTION

Table 11-1

Safety precautions 

The electric circult must be installed RCCB and manual switch  

Outdoor temperature:17~46°C

 Cooling 

operation

Dewetting 

operation

Intdoor temperature:≥17°C

Outdoor temperature:17~46°C
Intdoor temperature:17~32°C

Model

Air flow of the indoor unit

MCCU-03CN1A

500~650m

3

/h

MCCU-05CN1A
MCCU-07CN1A

700~900m

3

/h

1000~1250m

3

/h

Table 11-2

Air flow of the indoor unit

Summary of Contents for MCCU-03CN1A














Reviews: