(1) Fix two CO tube card on the red CO soft tube: (see Figure 6).
2
2
(2) Relate the ends of red CO soft tube respectively to CO intake port of mixed ball valve and
2
2
round outlet ofCO regulator valve. Lock it t firmly with the fixed card of two CO channel on red
2
2
CO soft tube: (see Figure 7)
2
(3) TightentheCO regulator table valve with hex nut port with the gas outlet of CO tank by the
2
2
wrench.(see Figure 8)
(4) Place the CO tank and CO regulator valve component into the beer chassis and fix theCO
2
2
2
tank by CO tank bracket and fixed bolt (see Figure 9)
2
3. Install CO gas cylinder and CO regulator valve:
2
2
4.
Install beer barrels
5.
Install wine handle and fix wine faucet
图6
Put the bottled beer into the box and make the barrel's hole connected to the beer kegs
connection port of the mixed ball valve closely. (See Figure 10) (when placing the kegs:
hold the handle of the barrels to remove them to the front of beer machine, and then
highlight the lower part of the front of beer keg to put them in the box. Finally, lift the
bucket handle of the keg to push them into the box entirely.)
Notes
Figure
6
Figure
7
Figure
5
Figure
8
When taking beer, open the main switch of CO gas cylinder, and rotate the regulator knob on CO regulator table's valve so that it reaches a
2
2
certain pressure value (observing regulator table).Furthermore, open the safety switch of CO regulator table valve and pull back the
2
mixed valve control handle, then lifting up. Loosen your grip to fix it: Close the door, and pull the beer tower components forward to get
beer.
?
When replacing the beer, please turn off the safety switch of CO regulator valve and remove the mixed ball valve to remove the beer barrel.
2
?
When replacing CO gas cylinder, remember to turn off the main switch of the CO gas cylinder and safety switch of the CO regulator valve.
2
2
2
Afterwards, use a wrench to loosen the hexagonal nut port connecting theCO regulator valve with CO tank closely. Then remove the fixed
2
2
bolt of CO tank to remove CO tank finally by a wrench.
2
2
?
In the process of installation, ensure that all parts are connected tightly and no air leaks.
?
When the hose connects the connection port, you can dip it by warm water or lubricated oil once confronted with any troubles.
?
If the high-pressure compressed gas in theCO tank is not handled properly, it could be dangerous:
2
1. Please the testing date of D.O.T in the cylinder neck before installation. If it is more than 5 years, don't use the product any more, and
bring it back to the gas supplier.
2.CO gas cylinder should be kept away from heat sources. The unused cylinders should be placed upright in ventilated cool place (preferably
2
70 degrees Fahrenheit).
?
Figure
10
2.Install the
beer tower assembly
and the mixed ball valve:
(1) Plug the beer tower assembly into the beer top cover to fix:
A.3.0 inch: does not require tower buckle. Put beer tower directly at the surface
hole of the beer machine roof. Fix the beer tower assembly with screws directly on
the roof of the beer machine. (See Figure 3)
B.2.5 inch: need tower buckle. Put the beer tower at the surface hole of the beer
machine with 60 degrees inclined, and rotate 60 degrees clockwise along the card
slot. Make the wine faucet is against the front side of beer machine. Fix the beer
tower with washers in the box. (See Figure 4)
(2)Take out the accessories of the mixed ball valve. Fix the beer outlet of the mixed
ball valve with the transparent hose of the beer tower components. (See Figure 5)
Figure
4
2.5 inch
3. 0inch
Figure
3
6.Install the
upper cover guardrail and water box
:
Screw the wine handle clockwise with the wine faucet tightly. Then connect the wine
faucet with beer tower components, and tighten it by a wrench. (See Figure 9)
CO regulator
2
valver
CO gas
2
cylinder
Bracket and retainer
of CO tank
2
Safety switch
Regulating
table
The red CO soft tube
2
CO gas cylinder
2
upper cover
guardrail
Beer barrels
Beer tower
water box
Place the upper cover guardrail , water box on the top of top cover. (See Figure 10)
Figure
9
Summary of Contents for WHS-209BESS1
Page 1: ...WHS 209BESS1...
