background image

 

MNBE-B, D, D3R, E Instructions 

(continued) 

 

Rev: A  Page 10  of  10 

Midnite Solar 

17722 – 67

Th

 Ave Ne 

Arlington, Wa 98223 USA 

Ph 360-403-7207 

Fax 360-691-6862 

This configuration utilizes the same 12 volt group 31 batteries, but hooked up for 48 volts. There 

are only 2 paralleled strings in this system. A second battery enclosure may be installed side by 

side or on top of each other for double the capacity.  

Rumors persist in the industry that the higher voltage battery banks will not supply as much 

power as a low (12V) bank. This is simply not true. Take 8 group 31 batteries. Each battery is 

rated at 105 amp hours at 12 volts. Each battery is thus good for 1260 watt hours. Eight of these 

batteries yields 10,080 watt hours. No matter how these batteries are configured, they will still be 

the same watt hour battery bank. Be careful when looking at “amp hour” ratings. You also need 

to consider the voltage. Volts times amp hours yields watt hours. This 10,080 watt hour battery 

bank conceivably could run a 10,000 watt light bulb for 1 hour or a 1 watt light bulb for 10,000 

hours. In power back up applications, count on using up 80% of the watt hour rating. In cyclic 

applications you should not go lower than 50% depth of discharge. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This configuration uses 6 volt sealed batteries that result in only one string.  

This is a 48 volt battery bank. You could add 3 more cabinets and have only 4 paralleled strings.  

 

 

MNBE-D With three shelves, Eight sealed 

batteries, Inverter and disconnects. 

Summary of Contents for MNBE-B











Reviews: