background image

This equipment is not designed for
maritime use or for use in mobile

installations such as caravans or air-
craft. However, under certain conditions
it may be possible for an installation in
these applications. Please contact the
nearest Miele dealer or the Miele Tech-
nical Service Department with specific
requirements.

Inspect the dishwasher for ship-
ping damage. Do not install or op-

erate a damaged unit. Contact the
place of purchase.

Ensure that any plastic wrappings,
bags etc. are disposed of safely

and kept out of the reach of babies and
young children. Danger of suffocation!

This dishwasher should only be in-
stalled under a continuous

countertop secured to adjacent
cabinetry.

Do not install this dishwasher be-
neath a cooking surface, oven or

any appliance that radiates heat.
High temperatures from these units may
damage the dishwasher.

Do not, under any circumstances
cut the intake hose or submerge in

liquid. This hose contains electrical
components that could cause injury or
property damage if cut or submerged.

Use

Only use the dishwasher if all pan-
els are properly in place.

Do not tamper with the controls.

To reduce the risk of injury, do not
allow children to play in, on, or

near the dishwasher.

Do not abuse, sit, or stand on the
door or baskets of the dishwasher.

Under certain conditions, hydrogen
gas may be produced in a hot

water system that has not been used
for two weeks or more. HYDROGEN
GAS IS EXPLOSIVE. If the hot water
system has not been used for such a
period, turn on all hot water faucets and
let water flow from each for several min-
utes before using the dishwasher. This
will release any accumulated hydrogen
gas. Do not smoke or use an open
flame during this time.

Do not wash plastic items unless
they are labeled "dishwasher safe"

or the equivalent. For items not labeled,
check the manufacturer’s recommenda-
tions.

IMPORTANT SAFETY INSTRUCTIONS

5

Summary of Contents for G 832 SC

















































Reviews: