background image

Mounting Accessories

The mounting accessories needed for
installing the appliance into the niche
are included in the packaging. Several
plastic bags are included which are
numbered alphabetically.

The bag needed for each step will be
marked with its respective letter.

Anti-tip brackets

The anti-tip brackets

a

keep the

appliance safely secured in the
installation niche

b

and prevent it from

tipping.

,

Risk of tipping

The installation niche must be
securely attached to the wall behind
it. This is the only way the
appliance, which is later secured in
the niche, can be prevented from
tipping!

Two anti-tip brackets are
recommended for each appliance. For
side-by-side installations 4 brackets are
recommended.

^

Position the anti-tip brackets on the
left and right in the installation niche
so that there is no more than 3/8"
(10 mm) of space between the
brackets and the side walls.

^

Mark the drill holes in the anti-tip
brackets on the back wall and on the
ceiling of the installation niche.

^

Set the brackets aside - they will be
needed again later.

Screws are supplied with the
appliance for various
applications/materials.

If the anti-tip brackets cannot be
attached securely with the screws
supplied, an alternative anti-tip
device can be used.

Assure that there are no electrical
wires in the area which the screws
could penetrate - risk of injury and
damage.

Installing the appliance

51

Summary of Contents for K 1803 Vi







































Reviews: