background image

Fault messages in the display

Problem

Possible cause

Remedy

A

;

lights up in the

display and

Drain fault

flashes.

– The water outlet is

blocked or
restricted.

– The drain hose has

been fixed too high.

– Clean the drain filter and

the drain pump.

– The maximum delivery

head is 1 m.

;

lights up in the

display and

Water inlet
fault

flashes.

The water inlet is
blocked or restricted.

Check whether

– the tap is opened properly.

– the inlet hose is kinked.

– the water pressure is too

low.

;

lights up in the

display and

Waterproof
fault

flashes.

The water protection
system has reacted.

Call the Service Department.

;

lights up in the

display and

Technical
fault

flashes.

There is a fault.

Start the programme again.
If the fault message appears
again, contact the Service
Department.

Anti-crease
Chk detergent

flashes in the display.

Excessive foam has
built up during
washing.

Use less detergent next time
and follow the manufacturer's
instructions on dosage given
on the packaging.

A

To switch off the fault message: Switch the machine off with

I-On/0-Off

button.

Problem solving guide

35

Summary of Contents for W 1611

































































Reviews: