background image

Extra options

50

You can supplement the wash
programs with extra options.

SingleWash

For efficiently washing a very small load
(< 2.2 lb/1 kg) in a normal wash
program. The wash duration is reduced.

Please note!

 

When adding detergent manually, only
use liquid detergent and use the proper
amount. Use a maximum of 50 % of the
specified amount of detergent for a ½
load. Chlorination is 

not

 possible.

Eco

The 

Eco

 extra option helps to save

energy. The wash temperature is
reduced and the wash duration is
increased in return. The wash program
continues to provide a deep clean.

SoftSteam

In order to reduce creasing, the laundry
undergoes a smoothing process at the
end of the program. Reducing the
maximum load by 50% will give a better
result. Please note the load information
in the display. Small loads give a better
result.

The garments must be suitable for
drying in a tumble dryer 

 

 and

suitable for ironing 

 

.

Extra Gentle

Drum rotation and wash duration are
reduced. Lightly soiled fabrics are
washed more gently.

Pre-wash

For laundry with large amounts of dirt,
e.g. dust and sand.

Pre-wash and chlorination is 

not

possible.
The chlorine bleach is added too
early.

Only liquid detergent may be added
to the 

 chamber of the

detergent dispenser drawer.
Powder detergent clogs up the

 chamber and water can

escape from the detergent dispenser
drawer.

Soak

For heavily soiled fabrics with protein
stains.

A soak duration of between 30 minutes
and 6 hours in 30-minute increments
can be selected for the soak process.
See “Settings” for more information.

The factory default setting is
30 minutes.

Summary of Contents for WXR 860





















































































































Reviews: