background image

WIRELESS VEHICLE DETECTION AT ITS BEST!!!

800-473-0213        ~        info@mierproducts.com        ~        www.mierproducts.com

600/605-Q22021

1

2

3

3

4

5

DA-600

DA-605

Page(s) 

Content                                                                                             

2-3  

DA-600 and DA-605

 Control Panel/Receiver Installation Guide

4-6 

 

Sensor/Transmitter Installation Guide

 

Installation Tips

 

Hooking Up Other Equipment to your Control Panel/Receiver

9   Accessories

10 

 

Long Range Installations

11 

 

Supplemental Specifications

12   Troubleshooting

13 

 

Technical Support Information and Warranty

1)  A sensor(s) detect(s) a vehicle entering monitored 
      area(s) . 
2)  A control panel up to 1000 feet away receives a 
      signal from the sensor and triggers an alert inside 
      the home or business (booster antenna increases 
      range to 3/4-mile)

3)  Add remote plug-in chimes in the  front room, 
     basement, upstairs, back yard, by the pool, or in 
     other buildings
4)  Add a Timer Control to turn on outdoor and in
     door lights to warn strangers or welcome friends
5)  Activate video surveillance to record activity and 
     display the driveway on a monitor
6)  Activate signs, gates, alarm panels or other 
     equipment
7)  Add a repeater to send the signal another 1000’ 
     to rrigger additional alerts in out buildings, or 
     add a booster-antenna for buildings up 3/4-mile 
     away

THE BASICS

MORE OPTIONS

Summary of Contents for DA-600














Reviews: