background image

30

  

TS571W Installation Instructions

TS571W Installation Instructions

  

31

For Your Records

Please record the product serial number (located on the right hand side of the control box), and the date and place of purchase in the 
spaces provided below. Refer to this information when calling Nortek Security and Control for service or assistance with your automatic 
gate operator. 

Serial Number ____________________________________________

Date of Purchase  _________________________________________  

Place of Purchase  ________________________________________  

Remember to keep all receipts for proof of purchase.

1.  First use the procedures found in the 

Maintenance & 

Troubleshooting Guide

 (see 

page 28

). 

2.  For 24 hour 7 days a week trouble shooting and 

support online go to our TECH WIZARD site at  

www.mightymule.com

3.   If you are unable to solve the problem, call the  

Tech Service Department at (800) 543-1236, or  
(850) 575-4144. 

4.   If repair or replacement of your gate operator is necessary, 

the Service Department will assign a Return Authorization 
(RA) number.

5.  Include a copy of your receipt and securely pack the 

component(s) authorized for return to the factory. Write the 
RA number issued to you on the outside of the package in 
LARGE BOLD PRINT. Ship the package(s) freight prepaid to 
the address provided during the RA process.

If your Mighty Mule Gate Opener is not operating properly, please follow the steps below:

NOTE:

 

Products returned to Nortek Security and Control without a Return Goods Authorization (RGA) 

number in LARGE BOLD PRINT on the outside of the package WILL NOT be accepted. Items returned 
to Nortek Security and Control freight collect WILL NOT be accepted. Items returned without proof of 
purchase will not be repaired under warranty.

The Mighty Mule Technical Service Department is open 

Monday – Friday 8:00 A.M. – 7:00 P.M. (Eastern Time)

Fax (850) 575-8950 • Web site: 

www.mightymule.com

Telephone (800) 543-1236

For 24 hour 7 days a week trouble shooting and support 

online go to our TECH WIZARD site at... 

www.mightymule.com

Repair Service

Summary of Contents for TS571W




























Reviews: