background image

x

  

TS571W Installation Instructions

TS571W Installation Instructions

  

xi

Technical Specifications

1. 

Determine Charging Option for Battery: Transformer OR Solar

IMPORTANT:

 

 

The transformer is designed for indoor use. If the transformer can be plugged only into an outside electrical outlet, a 
weatherproof cover/housing (available at local electrical supply stores) must be used. 

 

If your gate is more than 1000 ft. from an AC power source, you will need to use at least 10 watt solar charging power 
to charge the battery [FM123]. Refer to the Solar Panel and Gate Activity chart below.

 

All low voltage wire used with the Mighty Mule gate operator must be 16 gauge dual conductor, stranded, direct burial 
wire [RB509]. Do not run more than 1000 ft. of wire. 

NEVER USE TRANSFORMER AND SOLAR PANEL(S) AT  

THE SAME TIME. It will damage the control board.

The table and map illustrate 
the maximum number 
of gate cycles to expect 
per day in a particular 
area when using from 
10 to 30 watts of solar 
charging power prior to the 

battery depleting to a state where the unit will 
not function. The figures shown are for winter 
(minimum sunlight). Accessories connected to 
your system will draw additional power from the 
battery.
Deep cycle marine battery is recommended for 
solar and/or high traffic applications.

Before You Begin

POWERING OPTIONS

SOLAR PANEL AND GATE ACTIVITY CHART

Single Gate Winter Ratings

Zone 1

Zone 2

Zone 3

12 v single gate (10 watts) solar charger 

8

16

26

12 v single gate (20 watts) solar charger 

14

28

38

12 v single gate (30 watts) solar charger 

20

44

54

* Power increments are for reference only.

•  Low friction screw drive (linear actuator) rated for -5 ºF to +160 ºF (-20 ºC to +71 ºC). 

•  Opener length with push-pull tube fully retracted is 40.25", mounting point to mounting point. Maximum stroke is 20".

•  Maximum opening arc of 110º.  Approximate opening time (90º): 14 seconds, depending on weight of gate.

•  The system is powered by a 12 Vdc battery lead acid automotive or marine battery (not included). 

•  Battery charge is maintained by Mighty Mule transformer or optional Mighty Mule Solar Panels. 

•  The system uses 25 A Mini ATC blade-style fuses.

 

NOTE:

 The transformer should not be directly connected to any battery. Do not replace fuses with higher ampere rated  

 

fuses; doing so will void your warranty and may damage your control board.

•  Adjustable auto-close timer (OFF, 3 to 120 seconds), and Dual Sense Technology Entrapment Protection.

•  Accessory terminal block fully compatible with all Mighty Mule access controls.

•  Audio entrapment alarm sounds if unit encounters an obstruction twice while opening or closing.

MIGHTY MULE TS571W GATE OPENER

NOTE: Ball bearing hinges should be used on all gates weighing over 250 lb.

OPERATIONAL CAPACITY

The Gate Capacity Chart below shows the recommended maximum gate length to weight. The minimum recommended gate length 
is 5 ft.

* If the gate operator controller is OFF, the system will NOT charge the battery.

Maximum Weight (lbs.)

Maximum Length (ft.)

850

8

750

10

650

12

550

14

450

16

350

18

Summary of Contents for TS571W




























Reviews: