background image

The triangle shaped marks used in this manual and on the decals stuck on the 

main body indicate common hazards. Be sure to read and observe the cautions 

described.
                  Warning labels indicating hazards to humans and to equipment.

DANGER:

WARNING:

CAUTION:

General precautions

Warning labels

Denotes an extreme hazard. It calls attention to a procedure, 

practice, condition or the like, which, if not correctly performed 

or adhered to, is likely to result in serious injury or death.

Denotes a hazard. It calls attention to a procedure, practice, 

condition or the like, which, if not correctly performed or 

adhered to, could result in serious injury or death.

Denotes a hazard. It calls attention to a procedure, practice, 

condition or the like, which, if not correctly performed or 

adhered to, could result in injury to people and may damage or 

destroy the product.

Precautions (without a triangular mark): 

Failure to follow the instructions may 

result in damage to property.

Precautions for safety

WARNING

DO NOT 

work in the following conditions.

- If you do not feel well due to overwork or illness.

- If you are taking any medicine.

- If you are under the influence of alcohol.

For details about the engine, refer the separate instruction manual for the engine.

Make sure you thoroughly understand the construction and operation of the machine.

The decals on the machine body (operating methods, warning decals, etc.) are very 

important to ensure safety. Keep the machine body clean so that they can be read at all 

times. If any decal cannot be read, replace it with a new one.

It is very dangerous if children come into contact with the machine. Take the utmost care 

about how and where the machine is stored.

Before performing any maintenance, be sure to turn the engine off.

Mikasa does not accept any liability for accidents or problems caused as a result of not 

using genuine Mikasa parts (foot assembly, etc.), or if the machine has been modified.

CAUTION

Read this instruction manual carefully 

and handle the machine as described 

so that you can work safely.

T o   w o r k   s a f e l y ,   a l w a y s   w e a r  

protective clothing (helmet, safety 

glasses, safety shoes, ear plugs etc.) 

and appropriate work clothes.

Always check the machine to make 

sure that it is normal before starting 

operation.

2

Summary of Contents for MT-76D





















Reviews:

Related manuals for MT-76D