background image

16

Coincidental - XY or Crossed pairs

Coincidental microphone set ups are where the two microphones’ 
capsules are set close together on the same axis  The most common 
of these is XY or crossed pairs  In the XY set up, the two microphone 
capsules are positioned on the same axis, one directly above the other 
with the capsules positioned on an angle from 90 to 120 degrees  The 
wider the angle, the wider the stereo spread  Since the microphones are 
set on the same axis, the distance is constant and there’s little or no delay 
difference  Therefore, the stereo image is created by the level difference 
of the left and right microphones  Since there is no appreciable delay, 
there is less of a chance for phase cancelation and comb filtering so you 
can good results when the stereo signal is combined to a mono signal  
MS – Mid side

The Mid side technique makes use of two microphones, with one figure-8 
and a second mic either cardidod or omni , or two figure-8 pick patterns   
The first microphone (the mid), either figure-8, omni or cardioid 
microphone, is positioned facing directly at the sound source  The second 
microphone (the side), with a figure-8 pattern, is positioned on the same 
axis directly 

90

Applications Guide

Summary of Contents for CV4

























Reviews: