background image

 

3776 Greenbriar Drive * Stafford, Texas 77477 * PH: 713-266-1400 * FX: 713-789-1497 *  www.theultimatelock.com  

14. For your Records 

It is recommended that you record the details of your Ultimate Lock for future Reference. Each Ulti-
mate Lock

®

 comes with it’s own serial number.  If your insurance provider offers discounts, you can 

register your lock at our customer portal and print a certificate to give to your insurance company for a 
discount on your home/renters insurance. 

 

 

 

 

Date Purchased: 

__________________ 

 

 

 

 

Purchased From:  __________________

 

 

 

 

 

Serial Number:  

__________________ 

Serial 
Number 

13. Limited Warranty 

Every Ultimate Lock

®

 is thoroughly inspected before leaving the factory. It is warranted to be free of manu-

facturers defects for a period of TEN YEARS from the date of original purchase. Should any concerns de-
velop during the TEN YEAR period, please 

c

all our office 

866-MLS-4005 

for an evaluation prior to returning 

the product. Only components that are manufacturers defect need to be returned. Ship those components, 
prepaid, to Millennium Lock, Inc. 3776 Greenbriar Dr., Stafford, TX 77477. If our inspection shows the trou-
ble was caused by a manufacturers defect, Ultimate Lock

®

 will repair (or at our option) replace the lock/

component without charge. For warranty to go into effect you must register your Serial Number on line at 

www.theultimatelock.org/login.aspx 

 

Shipping Charges May Apply!

 

 
 

This Warranty does not apply where: 

• Repairs have been made or attempted by others • The lock has been abused, misused or improperly in-
stalled • Repairs are required because of normal wear and tear  • Alterations have been made to the lock or 
its components. 

 
 

In no event shall Ultimate Lock

®

 be liable for any indirect, incidental or consequential damages from the 

sale or use of the product. This disclaimer applies both during and after the term of the warranty. Ultimate 
Lock

®

  disclaims  liability  for  any  implied  warranties,  including  implied  warranties  of  “merchantability”  and 

“fitness for a specific purpose”, after the TEN-year term of this warranty. This warranty gives you specific 
legal rights, and you may also have other rights, which vary from state to state. Some states do not allow 
the exclusion or the limitation of incidental or consequential damages, so the above limitation or exclusion 
may not apply  to  you. Some states do not  allow limitation on  how long an  implied  warranty  lasts, so  the 
above limitation may not apply to you. 

*Disclaimer

The Ultimate Lock

®

 is only as strong as your door 

frame.

  Please contact your local locksmith to visit your home and evaluate your current setup.

 

Notes 

____________________________________________________________________________________________ 
 
____________________________________________________________________________________________ 
 
____________________________________________________________________________________________ 

Page 8 of 8 

Copyright© 2013 

All Rights Reserves 

Summary of Contents for Ultimate lock 3200 Series









Reviews: