background image

5082019

26

WARNING! This product(s) is designed for adult use only! No one under the age of 16 shall attempt to use this or any other 

product(s) without direct adult supervision. Failure to follow these instructions may result in serious injury or death!

WARNING! Do not attempt to use this and/or any other product(s) when ice, snow and/or freezing rain has deposited or formed 

on any portion of the tree you intend to climb. Failure to follow these instructions may result in serious injury or death! 

WARNING! Never attempt to either climb up or climb down with a weapon in your possession. ALWAYS unload your weapon 

and pull it up to hunting height using a tether or pull-up rope. ALWAYS lower your unloaded weapon down to the ground prior to 

attempting to climb down. Failure to follow these instructions may result in serious injury or death!

WARNING! Never attempt to hunt from an unlevel treestand. Additionally, never attempt to level your treestand at heights above 

the ground. If you find that your treestand is unlevel, canted, angled awkwardly upward or downward, or in any configuration 

other than level, immediately climb down to ground-level and readjust your treestand as necessary to alleviate this awkward 

angle. Failure to follow these instructions may result in serious injury or death!

We are very serious about your personal safety. A full-body fall arrest harness has been included with this product for your use. 

The full-body fall arrest harness system which meets or exceeds industry standards recognized by the TMA has been designed 

to keep you from experiencing a fall.

WARNING! Thoroughly inspect this or any other product(s) prior to each use for signs of wear, rot, corrosion, cracks, deteriora-

tion and/or any other type of defect. Protect this product from extended exposure to direct sunlight, excessive heat or freezing 

temperatures. Do not use this or any other product(s) if it shows evidence of wear, rot, corrosion, cracks, deterioration and/or 

any other type of defect. Failure to follow these instructions may result in serious injury or death!

Read the full-body fall arrest harness section (pages 8-14) carefully and follow all of the instructions! Your full-body fall arrest 

harness and its components (i.e., lanyard/tether, tree belt, climbing belt, Suspension Relief Device) is designed for a maximum 

capacity (user and equipment) of 300 pounds (136 kg). Additionally, your full-body fall arrest harness (and it components) must be 

replaced after three (3) years of service. Please contact Millennium for full-body fall arrest harness replacement procedures should 

you experience a fall or shall it exceed the three (3) year service period.

WARNING! Prior to attempting to use this or any other product(s) you must take a moment and become familiar with its assem-

bly, setup and installation. You must practice installing, setting-up and using this product(s) at ground-level prior to attempting 

to use it at heights above ground-level. Once you have become thoroughly knowledgeable and comfortable with this product(s) 

setup, installation and use at ground-level, you are now ready to use it at heights above ground-level. Failure to follow these 

instructions may result in serious injury or death!

WARNING! These ladderstands were designed to be used on trees with a MINIMUM DIAMETER OF 12” (30 cm) at treestand 

installation height (i.e., seating platform height ) and a MAXIMUM diameter of 22” (56 cm). DO NOT attempt to install on trees 

with smaller diameters. Failure to follow this warning may result in serious injury or death!

WARNING! Never install, set-up, or climb to your ladderstand with a weapon. Use a pull up rope to carefully raise your unloaded 

weapon after full-body fall arrest harness is secure and you are set in the stand. Failure to follow these instructions may result 

in serious injury or death!

WARNING! You must have at least three (3) adults to install and/or remove this ladder treestand. Failure to follow these instruc-

tions may result in serious injury or death!

WARNING!  STOP NOW!!!!! Make sure that you are wearing your full-body fall arrest harness. Failure to follow these 

instructions may result in serious injury or death!

STEP 1: Select a straight, healthy tree, one devoid of branches, vines or other obstructions which may encumber your 

ability to climb safety. The installation tree must have a minimum diameter of 12” (30 cm) at treestand installation height 

(i.e., seat height) or a maximum treestand installation diameter of 22” (56 cm).

WARNING! These Millennium product(s) were designed for installation on trees with a minimum diameter of 12” (30 cm) at 

treestand installation height (i.e., seat height) and a maximum treestand installation diameter of 22” (56 cm). DO NOT use your 

Millennium product(s) on trees with trunk diameters that do not meet this minimum diameter requirement. Failure to follow these 

instructions may result in serious injury or death!

STEP 2: Locate the two (2) stabilizing straps with cam buckles that were previously installed onto the ladder rails as 

shown in Figure 30.

WARNING! You must check the ground under the treestand to make sure it is firm and level. Sloping ground or uneven 

surfaces (e.g., one foot on a rock) can cause your ladder to tilt or shift off the tree as you climb. Failure to follow these 

instructions may result in serious injury or death!

Summary of Contents for OL'MAN OL-22-00































Reviews: