Milwaukee 4460 71 03, Original Instructions Manual

18

19

M18 CSX

..............................4526 75 03

..............................4489 72 03

..............................4460 71 03

   ...000001-999999

.....................300 mm

.......................20 mm

.......................25 mm

.......................25 mm

.....................150 mm

................0-3000 min

-1

....................28,6 mm

.......................18 V

......................4,1 kg

........................84,9 dB (A)

........................95,9 dB (A)

............................. 16,7 m/s

2

............................... 1,5 m/s

2

............................. 22,3 m/s

2

............................... 3,0 m/s

2

ENGLISH

 W

ARNING! Read all safety warnings and all instructions. Failure to 

follow the warnings and instructions may result in electric shock, fi re 

and/or serious injury. 

Save all warnings and instructions for future reference. 

 SABRE SAW SAFETY WARNINGS

Wear ear protectors.

 Exposure to noise can cause hearing loss.

Hold power tool by insulated gripping surfaces, when performing 

an operation where the cutting accessory may contact hidden 

wiring.

Cutting accessory contacting a „live“ wire may make exposed metal 

parts of the power tool „live“ and could give the operator an electric 

shock.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

Use protective equipment. Always wear safety glasses when working 

with the machine. The use of protective clothing is recommended, such 

as dust mask, protective gloves, sturdy non-slip footwear, helmet and 

ear defenders.
The dust produced when using this tool may be harmful to health. Do 

not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. 

asbestos).
Switch the device off  immediately if the insertion tool stalls! Do not 

switch the device on again while the insertion tool is stalled, as doing 

so could trigger a sudden recoil with a high reactive force. Determine 

why the insertion tool stalled and rectify this, paying heed to the safety 

instructions.
The possible causes may be:

•  it is tilted in the workpiece to be machined

•  it has pierced through the material to be machined

•  the power tool is overloaded

Do not reach into the machine while it is running.
The insertion tool may become hot during use.

WARNING! 

Danger of burns

•  when changing tools

•  when setting the device down
Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or fl oor, take care to avoid electric 

cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces 

can cause severe injury and damage.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft materials 

(wood, light building materials for walls). Harder materials (metals) 

must fi rst be drilled with a hole corresponding to the size of the saw 

blade.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by 

burning them. Milwaukee Distributors off er to retrieve old batteries to 

protect our environment.
Do not store the battery pack together with metal objects (short circuit 

risk).
No metal parts must be allowed to enter the battery section of the 

charger (short circuit risk).
Use only System 18 V chargers for charging System 18 V battery 

packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry 

rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load or 

extreme temperatures. In case of contact with battery acid wash it off  

immediately with soap and water. In case of eye contact rinse 

WARNING

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may 

be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent 

accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off  or when it is running but not 

actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the accessories, keep the 

hands warm, organisation of work patterns.

TECHNICAL DATA 

CORDLESS RECIPROCATING SAW

Production code...............................................................................................

   .....................................................................................................................

   .....................................................................................................................

Cutting depth max. in:

  Soft- wood ....................................................................................................

  Steel .............................................................................................................

  Aluminium ....................................................................................................

  Non-ferrous metal ........................................................................................

  Metal pipe.....................................................................................................

Stroke rate  ......................................................................................................

Lengths of stroke .............................................................................................

Battery voltage.................................................................................................

Weight according EPTA-Procedure 01/2003 ...................................................

Noise/vibration information

Measured values determined according to EN 60 745.

Typically, the A-weighted noise levels of the tool are:

  Sound pressure level (Uncertainty K=3dB(A)) .............................................

  Sound power level (Uncertainty K=3dB(A)) .................................................

Wear ear protectors!

Total vibration values (vector sum in the three axes) determined according 

to EN 60745.

Vibration emission value a

h

  Cutting boards ..............................................................................................

  Uncertainty K= .............................................................................................

  Cutting wooden beams ................................................................................

  Uncertainty K= .............................................................................................

ENGLISH

thoroughly for at least 10 minutes and immediately seek medical 

attention.

Warning! 

To reduce the risk of fi re, personal injury, and product 

damage due to a short circuit, never immerse your tool, battery pack or 

charger in fl uid or al-low a fl uid to fl ow inside them. Corrosive or 

conductive fl uids, such as seawater, certain industrial chemicals, and 

bleach or bleach containing products, etc., Can cause a short circuit.

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that the product described 

under “Technical Data” fulfi lls all the relevant regulations and the 

directives 2011/65/EU (RoHs), 2014/30/EU, 2006/42/EC, and the 

following harmonized standards have been used: 
EN 60745-1:2009 + A11:2010

EN 60745-2-11:2010

EN 55014-1:2006 + A1:2009 + A2:2011 

EN 55014-2:2015 

EN 50581:2012

Winnenden, 2017-11-30

Alexander Krug 

Managing Director 
Authorized to compile the technical fi le.
Techtronic Industries GmbH

Max-Eyth-Straße 10

71364 Winnenden

Germany

SPECIFIED CONDITIONS OF USE

This sabre saw cuts wood, plastic, and metal. It can cut straight lines, 

curves, and internal cut-outs. It cuts pipes and can cut fl ush to a 

surface.
Do not use this product in any other way as stated for normal use.

ELECTRIC BRAKE

The electric brake engages when the trigger is released, causing the 

blade to stop and allowing you to proceed with your work. Generally, 

the saw blade stops within two seconds. However, there may be a 

delay between the time you release the trigger and when the brake 

engages. Occasionally the brake may miss completely. If the brake 

misses frequently, the saw needs servicing by an authorized 

Milwaukee service facility. 
You must always wait for the blade to stop completely before removing 

the saw from the workpiece.

BATTERIES

Battery packs which have not been used for some time should be 

recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of 

the battery pack. Avoid extended exposure to heat or sunshine (risk of 

overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, after use, the battery packs have to be fully 

charged. 
To obtain the longest possible battery life remove the battery pack from 

the charger once it is fully charged.
For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 27°C and away 

from moisture

Store the battery packs in a 30% - 50% charged condition

Every six months of storage, charge the pack as normal.

BATTERY PACK PROTECTION

In extremely high torque, binding, stalling and short circuit situations 

that cause high current draw, the tool will stop for about 2 seconds and 

then the tool will turn OFF. 

To reset, release the trigger.

Under extreme circumstances, the internal temperatur of the battery 

could become to high. If this happens, the battery will shut down.

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous Goods Legislation 

requirements.
Transportation of those batteries has to be done in accordance with 

local, national and international provisions and regulations.
•  The user can transport the batteries by road without further 

requirements.

•  Commercial transport of Lithium-Ion batteries by third parties is 

subject to Dangerous Goods regulations. Transport preparation and 

transport are exclusively to be carried out by appropriately trained 

persons and the process has to be accompanied by corresponding 

experts.

When transporting batteries:
•  Ensure that battery contact terminals are protected and insulated to 

prevent short circuit.

•  Ensure that battery pack is secured against movement within 

packaging.

•  Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice

MAINTENANCE

The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and spare parts. Should components 

need to be replaced which have not been described, please contact 

one of our Milwaukee service agents (see our list of guarantee/service 

addresses).
If needed, an exploded view of the tool can be ordered. Please state 

the machine type printed as well as the six-digit No. on the label and 

order the drawing at your local service agents or directly at: Techtronic 

Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.

SYMBOLS

CAUTION! WARNING! DANGER!

Remove the battery pack before starting any work on 

the machine.

Please read the instructions carefully before starting 

the machine.

Accessory - Not included in standard equipment, 

available as an accessory.

Do not dispose electric tools, batteries/

rechargeable batteries together with household 

waste material.

Electric tools and batteries that have reached 

the end of their life must be collected separately 

and returned to an environmentally compatible 

recycling facility.

Check with your local authority or retailer for 

recycling advice and collection point.

European Conformity Mark

National mark of conformity Ukraine

EurAsian Conformity Mark.