22
23
ENGLISH
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for chips
and cracks, backing pad for cracks, tear or excess wear,
wire brush for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or install an
undamaged accessory. After inspecting and installing an
accessory, position yourself and bystanders away from the
plane of the rotating accessory and run the power tool at
maximum no-load speed for one minute.
Damaged
accessories will normally break apart during this test time.
h) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and shop apron capable of stopping
small abrasive or workpiece fragments.
The eye protection
must be capable of stopping fl ying debris generated by various
operations. The dust mask or respirator must be capable of
fi ltrating particles generated by your operation. Prolonged
exposure to high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment.
Fragments of workpiece or of a broken
accessory may fl y away and cause injury beyond immediate
area of operation.
j) Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting accessory
may contact hidden wiring.
Cutting accessory contacting a
"live" wire may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
k) Position the cord clear of the spinning accessory.
If you
lose control, the cord may be cut or snagged and your hand or
arm may be pulled into the spinning accessory.
l) Never lay the power tool down until the accessory has
come to a complete stop.
The spinning accessory may grab
the surface and pull the power tool out of your control.
m) Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag your
clothing, pulling the accessory into your body.
n) Regularly clean the power tool’s air vents.
The motor’s fan
will draw the dust inside the housing and excessive accumulation
of powdered metal may cause electrical hazards.
o) Do not operate the power tool near fl ammable materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants.
Using
water or other liquid coolants may result in electrocution or
shock.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged rotating
wheel, backing pad, brush or any other accessory. Pinching or
snagging causes rapid stalling of the rotating accessory which in
turn causes the uncontrolled power tool to be forced in the
direction opposite of the accessory’s rotation at the point of the
binding.
For example, if an abrasive wheel is snagged or pinched by the
workpiece, the edge of the wheel that is entering into the pinch
point can dig into the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump toward or away
from the operator, depending on direction of the wheel’s
movement at the point of pinching. Abrasive wheels may also
break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by taking
proper precautions as given below.
a) Maintain a fi rm grip on the power tool and position your
body and arm to allow you to resist kickback forces. Always
use auxiliary handle, if provided, for maximum control over
kickback or torque reaction during start-up.
The operator can
control torque reactions or kickback forces, if proper precautions
are taken.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power tool
will move if kickback occurs.
Kickback will propel the tool in
direction opposite to the wheel’s movement at the point of
snagging.
d) Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
Corners,
sharp edges or bouncing have a tendency to snag the rotating
accessory and cause loss of control or kickback.
e) Do not attach a saw chain, woodcarving blade or
toothed saw blade.
Such blades create frequent kickback
and loss of control.
Safety Warnings Specifi c for Grinding and Abrasive
Cutting-Off Operations:
a) Use only wheel types that are recommended for your
power tool and the specifi c guard designed for the
selected wheel.
Wheels for which the power tool was not
designed cannot be adequately guarded and are unsafe.
b) The guard must be securely attached to the power tool
and positioned for maximum safety, so the least amount
of wheel is exposed towards the operator.
The guard helps
to protect operator from broken wheel fragments and
accidental contact with wheel and sparks that could ignite
clothing.
c) Wheels must be used only for recommended
applications. For example: do not grind with the side of
cut-off wheel.
Abrasive cut-off wheels are intended for
peripheral grinding, side forces applied to these wheels may
cause them to shatter.
d) Always use undamaged wheel fl anges that are of
correct size and shape for your selected wheel.
Proper
wheel fl anges support the wheel thus reducing the possibility
of wheel breakage. Flanges for cut-off wheels may be different
from grinding wheel fl anges.
e) Do not use worn down wheels from larger power tools.
Wheel intended for larger power tool is not suitable for the
higher speed of a smaller tool and may burst.
Additional Safety Warnings Specifi c for Abrasive
Cutting-Off Operations:
a) Do not “jam” the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive depth of
cut.
Overstressing the wheel increases the loading and
susceptibility to twisting or binding of the wheel in the cut and
the possibility of kickback or wheel breakage.
b) Do not position your body in line with and behind the
rotating wheel.
When the wheel, at the point of operation, is
moving away from your body, the possible kickback may
propel the spinning wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a cut for
any reason, switch off the power tool and hold the power
tool motionless until the wheel comes to a complete stop.
Never attempt to remove the cut-off wheel from the cut
while the wheel is in motion otherwise kickback may
occur.
Investigate and take corrective action to eliminate the
cause of wheel binding.
d) Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter the
cut.
The wheel may bind, walk up or kickback if the power tool
is restarted in the workpiece.
e) Support panels or any oversized workpiece to minimize
the risk of wheel pinching and kickback.
Large workpieces
tend to sag under their own weight. Supports must be placed
under the workpiece near the line of cut and near the edge of
the workpiece on both sides of the wheel.
f) Use extra caution when making a “pocket cut” into
existing walls or other blind areas.
The protruding wheel
may cut gas or water pipes, electrical wiring or objects that
can cause kickback.
ENGLISH
TECHNICAL DATA
HD28 AG115
HD28 AG125
Angle Grinder
Production code
4179 47 02..
4179 53 02...
...000001-999999
4322 36 02...
...000001-999999
Battery voltage
28 V
28 V
Rated speed
9000 min
-1
9000 min
-1
D=Grinding disk diameter max.
d=Grinding disk hole diameter
115 mm
22,2 mm
125 mm
22,2 mm
b=Grinding disk thickness max..
6 mm (1/4")
6 mm (1/4")
b=Cutting disk thickness min. / max.
1,0 / 3 mm
1,0 / 3 mm
D=Grinding surface diameter max.
115 mm
125 mm
D=Wiring brush diameter max.
75 mm
75 mm
Thread of work spindle
M14
M14
Weight according EPTA-Procedure 01/2003
2,8 kg
2,8 kg
Noise/Vibration Information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
79 dB(A)
79 dB(A)
Sound power level (Uncertainty K=3dB(A))
90 dB(A)
90 dB(A)
Wear ear protectors!
Vibration total values (triaxial vector sum) determined
according to EN 60745.
Surface grinding:
Vibration emission value a
h,SG
5,5 m/s
2
5,5 m/s
2
Uncertainty K
1,5 m/s
2
1,5 m/s
2
Sanding
Vibration emission value a
h, DS
2,5 m/s
2
2,5 m/s
2
Uncertainty K
1,5 m/s
2
1,5 m/s
2
For other applications, e.g. Abrasive Cutting-Off Operations or Wire Brushing other vibration values could occur.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ. This may signifi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns
WARNING! Read all safety warnings and all
instructions
. Failure to follow the warnings and instructions
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
ANGLE GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding, Wire
Brushing or Abrasive Cutting-Off Operations:
a) This power tool is intended to function as a grinder,
sander, wire brush, or cut-off tool.
Read all safety
warnings, instructions, illustrations and specifi cations
provided with this power tool.
Failure to follow all
instructions listed below may result in electric shock, fi re and/
or serious injury.
b) Operations as polishing are not recommended to be
performed with this power tool.
Operations for which the
power tool was not designed may create a hazard and cause
personal injury.
c) Do not use accessories which are not specifi cally
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your power tool,
it does not assure safe operation.
d) The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can break and
fl y apart.
e) The outside diameter and the thickness of your accessory
must be within the capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately guarded or
controlled.
f) The arbour size of wheels, fl anges, backing pads or any
other accessory must properly fi t the spindle of the power
tool.
Accessories with arbour holes that do not match the
mounting hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
Summary of Contents for 4933432145
