Milwaukee M12 FIR14LR Original Instructions Manual Download

Page: 8 / 37

ENGLISH

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that the product described

under “Technical Data” fulﬁ lls all the relevant regulations and the

directives 2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the

following harmonized standards have been used:
EN 62841-1:2015

EN 62841-2-2:2014

EN 55014-1:2017

EN 55014-2:2015

EN IEC 63000:2018

Winnenden, 2019-05-06

Alexander Krug

Managing Director
Authorized to compile the technical ﬁ le.
Techtronic Industries GmbH

Max-Eyth-Straße 10

71364 Winnenden

Germany

BATTERIES

Battery packs which have not been used for some time should be

recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance

of the battery pack. Avoid extended exposure to heat or sunshine

(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully

charged, after used.
To obtain the longest possible battery life remove the battery pack

from the charger once it is fully charged.
For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 27°C and

away from moisture

Store the battery packs in a 30% - 50% charged condition

Every six months of storage, charge the pack as normal.

BATTERY PACK PROTECTION

In extremely high torque, binding, stalling and short circuit

situations that cause high current draw, the tool will vibrate for

about 5 seconds, the fuel gauge will ﬂ ash,and then the tool will turn

OFF. To reset, release the trigger.
Under extreme circumstances, the internal temperature of the

battery pack could raise too much. If this happens, the fuel gauge

will ﬂ ash until the battery pack cooled down. After the lights go oﬀ ,

the work may continue.

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous Goods

Legislation requirements.
Transportation of those batteries has to be done in accordance

with local, national and international provisions and regulations.
• The user can transport the batteries by road without further

requirements.

• Commercial transport of Lithium-Ion batteries by third parties is

subject to Dangerous Goods regulations. Transport preparation

and transport are exclusively to be carried out by appropriately

trained persons and the process has to be accompanied by

corresponding experts.

When transporting batteries:
• Ensure that battery contact terminals are protected and insulated

to prevent short circuit.

• Ensure that battery pack is secured against movement within

packaging.

• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice

MAINTENANCE

Use only Milwaukee accessories and spare parts. Should

components need to be replaced which have not been described,

please contact one of our Milwaukee service agents (see our list of

guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please

state the machine type printed as well as the six-digit No. on the

label and order the drawing at your local service agents or directly

at: Techtronic Industries GmbH, Max-Eyth-Straße 10,

71364 Winnenden, Germany.

SYMBOLS

CAUTION! WARNING! DANGER!

Remove the battery pack before starting any work on

the machine.

Please read the instructions carefully before starting

the machine.

Do not dispose electric tools, batteries/rechargeable

batteries together with household waste material.

Electric tools and batteries that have reached the end

of their life must be collected separately and returned

to an environmentally compatible recycling facility.

Check with your local authority or retailer for recycling

advice and collection point.
European Conformity Mark

Ukraine Conformity Mark

EurAsian Conformity Mark

ENGLISH

TECHNICAL DATA

CORDLESS INDUSTRIAL SCREWDRIVER

Production code..................................................................................

Tool reception .....................................................................................

No-load speed ....................................................................................

Torque max .........................................................................................

Battery voltage....................................................................................

Weight according EPTA-Procedure 01/2014 (2.0 Ah ... 6.0 Ah) .........

Recommended ambient operating temperature .................................

Recommended battery types..............................................................

Recommended charger ......................................................................

Noise/vibration information

Measured values determined according to EN 62841.

Typically, the A-weighted noise levels of the tool are:

Sound pressure level (Uncertainty K=3dB(A)) ................................

Sound power level (Uncertainty K=3dB(A)) ....................................

Wear ear protectors!

Total vibration values (vector sum in the three axes) determined

according to EN 62841.

Vibration emission value a

Impact tightening of fasteners of the maximum capacity of the tool

Uncertainty K = ................................................................................

WARNING Read all safety warnings, instructions,

illustrations and speciﬁ cations provided with this power tool.

Failure to follow all instructions listed below may result in electric

shock, ﬁ re and/or serious injury.

IMPACT DRIVER SAFETY WARNINGS

Hold power tool by insulated gripping surfaces, when

performing an operation where the fastener may contact

hidden wiring.

Fasteners contacting a „live“ wire may make

exposed metal parts of the power tool „live“ and could give the

operator an electric shock.

Wear ear protectors.

Exposure to noise can cause hearing loss.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

Use protective equipment. Always wear safety glasses when

working with the machine. The use of protective clothing is

recommended, such as dust mask, protective gloves, sturdy

non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health.

Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g.

asbestos).
Switch the device oﬀ immediately if the insertion tool stalls! Do not

switch the device on again while the insertion tool is stalled, as

doing so could trigger a sudden recoil with a high reactive force.

Determine why the insertion tool stalled and rectify this, paying

heed to the safety instructions.
The possible causes may be:

• it is tilted in the workpiece to be machined

• it has pierced through the material to be machined

• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.

• when changing tools

• when setting the device down

Sawdust and splinters must not be removed while the machine is

running.
When working in walls ceiling, or ﬂ oor, take care to avoid electric

cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped

workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by

burning them. Milwaukee Distributors oﬀ er to retrieve old batteries

to protect our environment.
Do not store the battery pack together with metal objects (short

circuit risk).
Use only System M12 chargers for charging System M12 battery

packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry

rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load

or extreme temperatures. In case of contact with battery acid wash

it oﬀ immediately with soap and water. In case of eye contact rinse

thoroughly for at least 10 minutes and immediately seek medical

attention.

Warning!

To reduce the risk of ﬁ re, personal injury, and product

damage due to a short circuit, never immerse your tool, battery

pack or charger in ﬂ uid or allow a ﬂ uid to ﬂ ow inside them.

Corrosive or conductive ﬂ uids, such as seawater, certain industrial

chemicals, and bleach or bleach containing products, etc., can

cause a short circuit.

SPECIFIED CONDITIONS OF USE

The cordless industrial screwdriver can be used to tighten and

loosen nuts and bolts wherever no mains connection is available.
Do not use this product in any other way as stated for normal use.

WARNING

The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in

EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diﬀ erent

applications, with diﬀ erent accessories or poorly maintained, the vibration and noise emission may diﬀ er. This may signiﬁ cantly increase the

exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched oﬀ or when it

is running but not actually doing the job. This may signiﬁ cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eﬀ ects of vibration and/or noise such as: maintain the tool and the

accessories, keep the hands warm, organization of work patterns.

M12 FIR14LR

M12 FIR38LR

.........................4743 71 01... .................4743 64 01...

...000001-999999

............................ 1/4" (6,35 mm).................. 3/8" (9,5 mm)

......................... 0-250 min

-1

....................... 0-200 min

-1

.............................. 54 Nm .............................. 75 Nm

.............................. 12 V.................................. 12 V