Milwaukee M18 BPFP-CCST, Original Instructions Manual

44

45

•  After each use, check all parts of the product for leaks. Return the 

product to an authorised service center for repair, if it has any.

•  The spray wand can be stored in the cradle.

•  For transportation, secure the product against movement or falling to 

prevent injury to persons or damage to the product.

•  Store the product in a cool, dry and well-ventilated place that is 

inaccessible to children. Keep away from corrosive agents such as 

garden chemicals and de-icing salts. Do not store outdoors.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still impossible to 

completely eliminate certain residual risk factors. The following 

hazards may arise and the operator should pay special attention to 

avoid the following:
Electric shock. Never spray liquid towards electrical sockets, cables, or 

appliances.
Contact with hazardous substances. Spray materials may be harmful if 

inhaled, ingested, or comes in contact with skin or eyes. Follow 

instructions carefully and wear appropriate protective equipment as 

prescribed in this manual.

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

SOLUTION

Low pressure

Not enough battery 

charge 

Charge the battery

No pressure

Not enough battery 

charge 

Charge the battery

Leaky

Connections are not 

connected properly, 

gaskets porous

Retighten connecting 

elements, replace sealing 

elements

Motor is not 

running

Battery empty or 

defective 

Recharge or replace the 

battery

No spray

Spray nozzles are 

blocked

Clean with compressed air 

or a suitable solvent

BLOCKED NOZZLES

If the nozzles are blocked, immediately turn off  the sprayer.
Ensure the battery door is closed securely.

Wear protective clothing such as gloves and eye protection.

Disassemble the nozzles and clean with clear water. Replace defective 

fi lters.

CLEANING THE TANK

1.  Ensure the battery door is closed securely.
2.  Remove the tank from the base and set on a level surface away 

from the base to prevent exposing the base to harsh chemicals.

3.  Remove the tank cup and fi ll it about one-third full with clean water. 

A small amount of mild household detergent may be added. If 

needed warm water (max. 50°C) can be used.Replace the cap and 

gently slosh the water around the tank.

4.  Install the tank and spray the water until the tank has been emptied. 

Make sure to direct the spray toward an area that will not be 

damaged by residue chemicals in the tank.

5.  Repeat the procedure with clean water until the tank is thoroughly 

clean. Wash outside of nozzles and dry with cloth.

6.  Wipe the outside of the tank with a clean, dry cloth.
7.  Allow all pieces to completely dry before reinstalling parts and 

storing the unit. Always reinsert strainer before replacing tank cap.

MAINTENANCE

Servicing requires extreme care and knowledge and should be 

performed only be a qualifi ed service technician. For service we 

suggest you return the product to an authorized service center for 

repair. When servicing, use only identical replacement parts.
Only make adjustments or repairs described in this manual. For other 

repairs, contact an authorised service centre.

After each use, clean the product as prescribed in this manual.
Drain and empty the spray tank before cleaning.
Drain the spray materials through the fi ll area.
Drain all of the spray materials from the spray tank into a container 

approved for chemicals. Do not store chemicals in the spray tank.
Use clean water to clean and rinse the spray tank. A small amount of 

mild household detergent may be added. 
Wipe the product with a clean, dry cloth.
It may be necessary to rinse the spray tank more than once.

Cleaning electrical contacts

Keep electrical contact posts between bottom of tank and base clean. 

WARNING! 

Remove battery pack from tool before cleaning electrical 

contacts. Clean contacts with a dry, clean cloth only.

Tank 

Contacts 

Base

Disposal

Never dispose residual chemicals or contaminated rinsing solutions in 

waterways, drains, sewers, street gutters, or manholes.

Dispose residual chemicals and used containers in accordance with 

local waste disposal regulations.

ACCESSORIES

Use only Milwaukee accessories and spare parts. Should components 

need to be replaced which have not been described, please contact 

one of our Milwaukee service agents (see our list of guarantee/service 

addresses).
If needed, an exploded view of the tool can be ordered. Please state 

the machine type printed as well as the six-digit No. on the label and 

order the drawing at your local service agents or directly at: Techtronic 

Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.

ENGLISH

ENGLISH

SYMBOLS

CAUTION! WARNING! DANGER!

Please read the instructions carefully before starting the 

machine.

Remove the battery pack before starting any work on 

the machine.

Do not dispose electric tools, batteries/rechargeable 

batteries together with household waste material.

Electric tools and batteries that have reached the end of 

their life must be collected separately and returned to 

an environmentally compatible recycling facility.

Check with your local authority or retailer for recycling 

advice and collection point.
Always wear eye protection!

Wear ear protectors! 

Wear a suitable protection mask.

Use protective clothing

Wear gloves!

Wear sturdy non-slip shoes!

Do not expose battery to rain. Do not use battery in 

damp or wet locations.

Do not spray fl ammable liquids

Class III electrical protection.

4x

Remove the battery pack.

Keep electrical contacts clean.

Keep bystanders a safe distance away from work area!

Do not spray at people or animals!

Do not spray at a wall!

Do not spray against the wind!

Do not point the nozzle upwards! Only spray 

downwards!

Empty weight (including baseunit, tank, 

battery)

V

Volts

Direct current

European Conformity Mark

Ukraine Conformity Mark

EurAsian Conformity Mark