3
above
130
°
C
(
265
°
F
) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions.
Charging im-
properly or at temperatures outside the specified range
may damage the battery and increase the risk of fire.
SERVICE
• Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
• Never service damaged battery packs.
Service
of battery packs should only be performed by the
manufacturer or authori
s
ed service providers.
NAILER SAFETY WARNINGS
• Always assume that the tool contains fasteners.
Careless handling of the nailer can result in unexpected
firing of fasteners and personal injury.
• Do not point the tool towards yourself or anyone
nearby.
Unexpected triggering will discharge the fas-
tener causing an injury.
• Do not actuate the tool unless the tool is placed
firmly against the workpiece.
If the tool is not in con-
tact with the workpiece, the fastener may be deflected
away from your target.
• Disconnect the tool from the power source when
the fastener jams in the tool.
While removing a
jammed fastener, the nailer may be accidentally acti
-
vated if it is plugged in.
• Use caution while removing a jammed fastener.
The mechanism may be under compression and the
fastener may be forcefully discharged while attempting
to free a jammed condition.
• Do not use this nailer for fastening electrical
cables.
It is not designed for electric cable installa-
tion and may damage the insulation of electric cables
thereby causing electric shock or fire hazards.
•Prior to each use, check workpiece contact and
trigger for correct operation.
Do not disassemble or
clamp parts of the workpiece contact, trigger, or driv-
ing mechanism. This will cause unexpected actuation,
resulting in serious injury.
•Do not engage in horseplay.
The discharged fasten-
ers are projectiles capable of causing serious injury.
•Do not remove, tamper with, or otherwise cause
the tool operating controls to become inoperable.
This will cause unexpected actuation, resulting in
serious injury.
•Do not operate a tool if any portion of the tool oper-
ating controls is inoperable, disconnected, altered,
or not working properly.
This will cause unexpected
actuation, resulting in serious injury.
•Always keep hands and body away from discharge
area of the tool.
Never attempt to clear a jammed
workpiece contact by grasping the discharge area of
the tool. Fasteners discharged from tool can cause
serious injury if they contact hands or body.
•Do not drive fasteners close to the edge of the
workpiece.
Fasteners can slip off corners and edges
or penetrate through thin material, making them pro-
jectiles capable of causing serious injury.
•Use the tool only for the intended purpose. Do not
abuse the tool.
Do not use as a hammer, stamp or en-
grave information onto parts, drop or impact the tool or
otherwise apply excess force to the tool in use. Do not
mount the tool to stands or modify it for stationary use.
•
Maintain labels and nameplates.
These carry
important information. If unreadable or missing, contact
a
MILWAUKEE
®
service facility for a replacement.
•
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.
SYMBOLOGY
Volts
Direct Current
Solid Light -
Single Sequential Actuation
Flashing Light -
Contact (Bump) Actuation
Read Operator's Manual
Wear Eye Protection
Keep Hands Away
•
WARNING
The power tool is under high
pressure and the striker has been
lifted to the ready-to-fire position. If a battery is placed
on the power tool and the trigger and workpiece
contact are actuated, the tool could fire.
Additional safety warnings
SPECIFICATIONS
Volts ............................................................. 18 DC
Battery Type .................................................M18™
Charger Type ...............................................M18™
Cat. No....... M18CN16GS-0C
16 Ga Straight Finish Nailer
Fastener Length ............................ min. 19mm (0.75")
............................ max. 63mm (2.5")
Fastener Length ............................ min. 31mm (1.25")
............................ max. 63mm (2.5")
Collation Angle ......................................................... 0°
Fastener Size (Diameter) ................... 16 Ga / 1.6 mm
Magazine Capacity ........................................110 nails
Cat. No ........M18CN16GA-0C
16 Ga Angled Finish Nailer
Collation Angle ....................................................... 20°
Fastener Size (Diameter) ................... 16 Ga / 1.6 mm
Magazine Capacity ....................................... 110 nails
Fastener Length ............................ min. 32mm (1.25")
............................ max. 63mm (2.5")
Cat. No ........M18CN15GA-0C
15 Ga Angled Finish Nailer
Collation Angle ....................................................... 34°
Fastener Size (Diameter) ................... 15 Ga / 1.8 mm
Magazine Capacity ....................................... 110 nails
Summary of Contents for M18CN16GA-0C
Page 7: ......
