5-11
Warning / Error Messages
5
Tr
oubleshooting
Message
Cause
Solution
An error occurred in the wiper con-
trol.
Turn off the main power to the machine
and turn it on after a while.
If the same error message appears again,
contact your local distributor to call for ser-
vice.
Paper could not be detected.
The media set position or media
itself is not proper.
If the same error message appears again
even after setting the media properly, con-
tact your local distributor to call for service.
The set position of the media is not
proper. The media detection has not
completed.
Set the media to the proper position again.
(
P.2-8, P.2-14)
Y-origin could not be detected.
Turn off the main power to the machine
and turn it on after a while.
If the same error message appears again,
contact your local distributor to call for ser-
vice.
The room temperature is out of the
usable temperature range (too low).
Adjust the room temperature of the instal-
lation place. (
P.3-38)
The room temperature is out of the
usable temperature range (too
high).
There is a slot where no cartridge
has been inserted.
Set a cartridge.
An error occurred on the head unit
memory.
Turn off the main power to the machine
and turn it on after a while.
If the same error message appears again,
contact your local distributor to call for ser-
vice.
The head is not connected.
An error occurred on the head slider
board.
The head is not MIMAKI genuine.
A SD-RAM of the size required for
the machine has not been
equipped.
Turn off the main power to the machine
and turn it on after a while.
If the same error message appears again,
contact your local distributor to call for ser-
vice.
(When a usable SD-RAM is available, the
machine can be started as is. However, a
printing speed may be slow depending on
resolution. )
An error is detected on the wave-
form printed on the lower line of the
display.
Turn off the main power to the machine
and turn it on after a while.
If the same error message appears again,
contact your local distributor to call for ser-
vice.
Model ID of main PCB is different.
(XX is ID code.)
An abnormal temperature of the
media heater was detected.
* * * * * E RROR 4 6 * * * * *
W I P E R
* * * * * E RROR 5 0 * * * * *
ME D I A W I D T H S E N SOR
* * * * * E RROR 5 0 * * * * *
ME D I A S E T POS I T I ON L
* * * * * E RROR 5 0 * * * * *
ME D I A S E T POS I T I ON R
* * * * * E RROR 5 1 * * * * *
Y - OR I G I N
* * * * E RROR 1 2 0 * * * *
ROOM T EMP L OW ( X X
° C )
* * * * E RROR 1 2 1 * * * *
ROOM T EMP H I GH ( X X
° C )
* * * * E RROR 1 4 4 * * * *
C A R T R I DGE S E T !
* * * * E RROR 2 0 0 * * * *
H E A D MEMOR Y ( - - - - )
* * * * E RROR 2 0 2 * * * *
D V E I C E CON S T RUC T I ON
* * * * E RROR 2 0 3 * * * *
S DR AM S I Z E
* * * * E RROR 2 0 7 * * * *
X X X X X X X X X X
* * * * E RROR 2 0 8 * * * *
C H E C K MA I N P C B I D X X
* * * * E RROR 2 1 1 * * * *
H e a t e r T EMP ( - - / - - / - - )
Summary of Contents for JV33-130
