MIMAKI UJF-6042MkII Series, Manual

For safe operation

6

Never do the following

WARNING

Do not disassemble or remodel the machine

• Never disassemble or remodel this machine and the

ink bottle.

Disassembling or remodeling any of them will result in

electric shocks or breakdown of this machine.

Power supply and voltage

• Use this machine with indicated power specifications.

Be sure to connect the power cable plug to the

grounded outlet, or it may cause fire or electric shock.

• Never look at the LED UV being lit with your naked

eyes, or it may cause pain in your eyes or visual

impairment. Be sure to wear safety glasses.

• Do not apply ultraviolet (UV) light directly to your skin,

or it may cause irritation on your skin.

• To prevent electrical shock, be sure to set OFF the

main power circuit breaker and disconnect the power

plug before carrying out maintenance. For some units,

capacitors may take one minute for discharging;

therefore, start maintenance work three minutes after

setting OFF the main power circuit breaker and

disconnecting the power plug.

• If LED UV has been damaged, you should replace the

LED UV that has reached or has past its rating life.

• The main power circuit breaker should be set ON only

by personnel with sufficient knowledge about

operations of this machine.

• Do not touch the lamp with bare hands while lighting or

right after the lamp off to avoid from burn injury.

• Although this device is a Class 1 laser device, its laser

sensors are equipped with Class 2 lasers. Never look

directly at the laser light, as it can make your eyes hurt

or damage your eyesight.

Do not use this machine in damp places

• Avoid damp environment to use this machine. Do not

splash water onto this machine. High humidity or water

will give rise to fire, electric shocks or breakdown of

this machine.

Abnormal event occurs

• If the machine is used under an abnormal condition

where the machine produces smoke or unpleasant

smell, fire or electric shocks can result. Be sure to turn

off the power switch immediately and detach the plug

from the receptacle. Check first to be sure that the

machine no longer produces smoke, and contact a

distributor in your district for repair.

• Never repair your machine by yourself since it is very

dangerous for you to do so.

Handling of ink bottles

• Some of the ingredients (UV Curing initiator) have

toxic consequences to aquatic life. Avoid leak into

water system or sewage containing water.

• Store ink bottles and waste ink tank in a place that is

out of the reach of children.

• If ink settles on the skin or clothes, immediately wash it

off with detergent or water. If you get ink in your eyes,

immediately wash your eyes with a lot of clean water,

and then consult a doctor as soon as possible.

Handling of the power cable

• Use a power cable attached to this machine.

• Take care not to damage, break or work on the power

cable. If a heavy things are put on the power cable,

heated or drawn, the power cable can break to cause

fire or electric shocks.

Handling of LED UV

• Do not use the LED UV in an ambience with a

possibility of catching fire (gasoline, combustible gas

spray, thinner, lacquer, powder dust, etc.). In addition,

do not put paper or cloth near or on the LED UV, or it

may cause fire, or it may cause electrical shock.

Handling of the antifreeze liquid

• Use the exclusive antifreeze liquid, or the cooling

device may be damaged.

• If the antifreeze liquid or mixed soft water with

antifreeze liquid gets on the skin or clothes,

immediately wash it off with soap.

If you get the antifreeze liquid in your eyes,

immediately wash your eyes with a lot of clean water.

Then, consult a doctor as soon as possible.

• Before using the antifreeze liquid, be sure to read the

Material Safety Data Sheet (SDS).

• If you swallowed the antifreeze liquid accidentally, try

to get to vomit, and then consult a doctor as soon as

possible.

• Discard the waste antifreeze liquid or used mixed soft

water with antifreeze liquid as follows;

Absorb in a sawdust or waste cloth, then incinerate it.

• Entrust to an industrial waste disposal contractor,

clarifying their contents.

• Avoid causing ignition with static electricity, impact

spark and so on.

• Be sure to wear goggles and gloves for handling the

antifreeze liquid.

Circulating water

• If you find any water leaks on the maintenance

parts, turn the power switch off immediately,

and remove the power plug from the power

socket.

Note on maintenance

• When cleaning the ink-station or the heads, make sure

to wear the attached goggles and gloves.

• The gloves supplied with the machine are disposable.

When all the gloves are expended, purchase an

equivalent product on the market.

WARNING