background image

MINDS-i®

 

is a high-performance Construction/RC/Robotics System, which is NOT intended for use on the public roads or congested 

areas where its operation may conflict with or disrupt pedestrian or vehicular traffic. Read all enclosed information before operating. 

Fully illustrated, step-by-step instructions describe adjustment, operation, and required maintenance procedures. MINDS-i® should not 

be operated in a crowd, or without adequate space. In an effort to continually upgrade our products, MINDS-i® reserves the right to make 

improvements and modifications to this system, which may not be reflected in the photographs and specifications printed on this box. 

PROPOSITION 65 WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects or 

other reproductive harm.

Terms & Conditions:

 

All orders placed with MINDS-i, Inc (phone, fax, mail, internet/web & email) constitute the acknowledgment 

and acceptance of all conditions listed below.  All purchases remain the property of MINDS-i®, Inc until paid for in full.  All orders shipped 

to a Washington State address must pay sales tax as required by the Washington State Department of Revenue.  In the event that an order 

placed on our web-site does not calculate sales tax and the order is being shipped to a Washington State address, MINDS-i® will calculate 

the sales tax when the order is processed and call or email the customer with the new amount.  All prices, materials, design, color, contents 

included with a product and product specifications are subject to change without notice.   Some product images may be shown with 

optional items that are sold separately.  Depending on the products ordered and the destination of the order, certain shipping services may 

not be available.  MINDS-i® will not be responsible for pricing errors and may cancel the order. Orders will not be shipped until all Credit 

Card information is verified and matched.  All other orders (check or money order) will not be shipped until payment has been received in 

full.  All unpaid orders will be canceled after 30 calendar days. All weights shown for products are used for shipping calculation only and 

may not reflect actual weight of the product.

Product Warranty:

 MINDS-i® warrants to the original buyer that our products are free from defects in materials and workmanship for 

a period of 120 days from the original date of purchase (original purchase receipt required). This warranty does not cover abuse, misuse, 

incorrect wiring, modifications, alterations, connector damage, wear and tear or robot competition damage.  If the Product is determined to 

be defective within the warranty period, MINDS-i® or its authorized service provider will, at our sole option, repair or replace any defective 

parts free of charge, or refund the purchase price.  What you must do: Return the Product in its original packaging or packaging affording 

equal protection, freight prepaid, with proof of purchase, to an authorized MINDS-i® service provider. You are responsible for all shipping 

charges.  For more information, contact MINDS-i® at (509) 252-5767 or info@mymindsi.com.

Shipping Errors and Defective Products:

  Claims for shipping shortages, errors, or defective materials must be in writing and 

received by MINDS-i® within ten (10) days after receipt of shipment by buyer. Failure to make such claim within the stated period shall 

constitute an irrevocable acceptance of the goods and an admission that the goods fully comply with all the terms and conditions of the 

buyer’s order.

MINDS-i® is Designed and Manufactured in the United States

Some components are manufactured in China and the Philippines.

Patents US 7,517,270; US 7,410,225; US 7,736,211; US 7,841,923; MX 288350; CN ZL 200680044576.1; Additional Patents Pending.

Trademarks 3,420,137 and 3,487,694

Copyright © 2014 MINDS-i Inc.  All rights reserved. 

MINDS-i, Inc

22819 East Appleway Avenue

Liberty Lake, WA  99019

USA

- 2 -

Summary of Contents for AMT-6X65-000



























Reviews: