background image

3.2 Technical Data

Protection classes

per DIN EN 60529

IP65:

Dust-proof and leak-proof against water jets (nozzle)

from any angle.

Installation position

Cable entry from below

Quantity of load cells

1…4

Pressure equalization

Plastic pressure equalization element

Material of the junction box

ABS

Color of the junction box

gray, similar to RAL 7035

Net weight

0.65 kg

Shipping weight

0.85 kg

Service temperature area

-30°C…+70°C

Storage temperature range

-30°C…+80°C

Cable screw connections

Plastic cable screw connections

Polyamide PA6 V-2

Insulation impedance (in service temperature range at

95% air humidity and U

DC

= 500 V)

>1000 M

3.3 Electromagnetic Compatibility (EMC)

All data in compliance EN 61326 industrial section

High frequency electromagnetic ields

(80…3000 MHz)

EN 61000-4-3

10 V/m

Housing

Electrostatic discharge (ESD)

EN 61000-4-2

6/8 kV

Fast transients (burst)

EN 61000-4-4

1 kV

Peak voltages (surge) 1.2/50 µs

EN 61000-4-5

1 kV

Signal and control

lines

Conducted disturbances by high fre-

quency coupling (0.15…80 MHz)

EN 61000-4-6

10 V

Cable Junction Box MP 90/04

3 Speciications

EN-8

Minebea Intec

Summary of Contents for MP 90/04

























Reviews: