Minebea Intec PR 5230 Instrument Manual Download | Manualshive

Page: 145 / 303

background image

[Measuretime]

Measuring time: The duration of a measurement can be selected.

Selection: 5 ms, 10 ms, 20 ms, 40 ms, 80 ms, 160 ms, <320 ms>, 640 ms, 960 ms,
1280 ms, 1600 ms.

[Digital filter]

Selection of the digital filter (filter characteristic): <off> (no Filter), Bessel, aperiod.
(aperiodic), Butterw. (Butterworth), Tcheby. (Tschebyscheff)

The following includes examples of interference signals for the different filter types:

Bessel filter

Aperiodic filter

Butterworth filter

Tschebyscheff filter

A digital filter can be switched on only with the measuring time set to <160 ms.

If no particularly frequent fluctuations are expected in ongoing operation, the following
settings are recommended:

[Measuretime]: <160 ms

[Digital filter]: aperiod.

[Fcut]: 2.00 Hz

[Fcut]

This line only is shown if the digital filter is switched on.

The smaller the cut-off frequency, the slower the measurement and the more stable the
measurement result.

Transmitter in field housing PR 5230

7 Commissioning

Minebea Intec

EN-142

«
...
143
144
145
146
147
...
»

Summary of Contents for PR 5230
















































































































































































































































































































Reviews:

No comments

Related manuals for PR 5230

Brand: YOKOGAWA Pages: 48

vigilantplant EJA Series

Brand: YOKOGAWA Pages: 79

EchoStream EN1215EOL

Brand: Inovonics Pages: 2

STORM PRO C-4014

Brand: Feniex Pages: 13

Brand: Vector Pages: 3

Brand: TTI Pages: 39

Brand: TILLQUIST Pages: 15

DpharpEJX vigilantplant EJX510A

Brand: YOKOGAWA Pages: 49

Brand: Retekess Pages: 2

Brand: Mun Ah Plastic Electronic Toys Pages: 3

BTL7-A/E1 0-M-H-SA262-KA Series

Brand: Balluff Pages: 16

Brand: Icom Pages: 78

Brand: Icom Pages: 124

VHF MARINE TRANSCEIVER IC-M501EURO

Brand: Icom Pages: 34

MMT-1P-480V-500VA-220V

Brand: Larson Electronics Pages: 2

Brand: Titanium Pages: 4

Brand: WIKA Pages: 60

Brand: Midland Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands