Minebea Intec PR 5230 Instrument Manual Download

Page: 196 / 303

Card test:

The device display shows the fieldbus card status.

Under

- [HW-Slots] - [Slot 2] all inputs and outputs are displayed.

Procedure:

Note:

Further details can be found in the supplementary application manual "How to

(available upon request from technical.support.hh@minebea-intec.com).

Note:

See Chapter "Description of the I/O Area"

Example:

The gross weight should be read.

I/O size = 8 bytes, counted from byte 0–7

7.15.6

Network parameters

Under this menu item, you can define the network parameters for the network
connections (built-in LAN adapter).

Open the menu via

- [Network parameter].

[HW address]

This parameter cannot be changed because the fixed address is specified by the
instrument.

Enter the IP address and network mask under

- [Fieldbus parameter] and

confirm.

Select and insert the instrument from the catalog into the I/O configuration.

7 Commissioning

Transmitter in field housing PR 5230

EN-193

Minebea Intec

Summary of Contents for PR 5230
















































































































































































































































































































Search results

Summary of Contents for PR 5230

Reviews:

Related manuals for PR 5230

Brands by name

Popular brands

Minebea Intec PR 5230, Instrument Manual

Search results

Summary of Contents for PR 5230

Reviews:

Related manuals for PR 5230

Brands by name

Popular brands