Minebea Intec PR 5230 Instrument Manual Download

Page: 290 / 303

Note:

VNC text, see also Chapter

16.1

LED

E:Arith

E:Invrs

E:Overl

E:NoSig

E:Sense

E:HardE/ E:NoCom

Flash. 1Hz

Altern. flash. 1Hz

Flash. 1Hz

Altern. flash. 1Hz

Flash. 1Hz

Altern. flash. 1Hz

Note:

With all other messages, the upper status indicator LED blinks.

16.3 Error messages for xBPI scales

Display

VNC text

Error and possible cause

Remote dis-
play

E:NoSig

Ext. meas. device error

No weight values can be read from scale:

Scale error

Error 3

E:Value

Value exceeds display

The weight value is not displayed:

Too many digits have been set.

Error 4

E:NoCom

No values from scale

No communication with xBPI scale:

Cable break.

Internal scale error.

The scale is not connected to the power sup-
ply.

Error 9

E:NoWgt

No weight data

No weight display:

Another weighing point was selected.

Press

to assign the new weighing point to

the device.

Error •

16 Error messages

Transmitter in field housing PR 5230

EN-287

Minebea Intec

Summary of Contents for PR 5230
















































































































































































































































































































Search results

Summary of Contents for PR 5230

Reviews:

Related manuals for PR 5230

Brands by name

Popular brands

Minebea Intec PR 5230, Instrument Manual

Search results

Summary of Contents for PR 5230

Reviews:

Related manuals for PR 5230

Brands by name

Popular brands